1998 JEEP WRANGLER Recalls, Complaints & Safety

Frame started showing signs of rusted out frame in 2003 when the transmission skid weld nuts in the bottom of the frame rusted out as well as the body side step weld nuts in the frame. In 2010, 3 or the 4 rear axle control arms broke free from the frame causing brake lines to fail while driving. I was able to use parking brake and downshifting manual transmission to get home. I was lucky that the rear axle didn't completely separate or the failed brake cause a serious accident. The TJ frames are poorly designed with no drainage causing them to rust from the inside out.

AIRBAG LIGHT COME ON AND SPEEDO AND TACH STOPS WORKING. VEHICLE HAS NOT BEEN IN AN ACCIDENT AND THIS IS OCCURING ON NUMEROUS JEEPS OF THIS YEAR. WHY HAS THERE NOT BEEN A RECALL? IF SOMETHING ISN'T DONE ABOUT THIS I WILL BE GETTING A LOT OF JEEP OWNERS TOGETHER AND FILING A CLASS ACTION LAWSUIT!! IT IS A SERIOUS SAFETY PROBLEM. I JUST PURCHASED THE VEHICLE AND AFTER RESEARCHING THIS ITS HAPPENING TO THE MAJORITY ON THIS YEARS WRANGLERS

JEEP WRANGLER FRAMES RUST FROM INSIDE OUT DUE TO MOISTURE GETTING IN THROUGH UPPER PART OF FRAMES WHERE THEIR ARE HOLES AND SETTLING TO LOWER PART OF FRAME WHERE THEIR ARE NO DRAIN HOLES. THEIR MAY HAVE NOT BEEN AN ISSUE IF JEEP HAD JUST PUT IN DRAIN HOLES IN LOWER PART OF FRAME. IT IS A COMMON PROBLEM IN 1997 THROUGH 2006 JEEP WRANGLERS. I HAVE THIS ISSUE.

JEEP TJ FRAME SEPARATED AT THE TORSION BAR ON PASSENGER REAR WHEEL MAKING VEHICLE UNSTABLE AND UN- USABLE.

MY FRAME IS ROTTING OUT FAST AND FURIOUS, I'VE ALREADY HAD TO REPLACE SECTIONS, THE UPPER AND LOWER CONTROLS ARMS HAVE RIPPED OFF, THE BODY FELL THREW THE MOUNTS, PAID TO HAVE THAT FIXED

I HAVE A 1998 JEEP WRANGLER. I'VE OWNED MY JEEP FOR 15 YEARS. IT HAS BEEN GARAGE KEPT. WE WERE CHANGING THE SHOCKS A FEW WEEKS AGO AND NOTICED SEVERE RUST DAMAGE. THE FRAME IS RUSTING FROM THE INSIDE OUT. IT'S SEVERE. YEARS BEFORE I WAS TRAVELING DOWN A 2 LAND RD AND HAD TO PRESS MY BRAKES HARDER THAN I USUALLY WOULD DUE TO A CAR PULLING OUT IN FRONT OF ME. AT THAT MOMENT I BLEW A BRAKE LINE. I COULD NOT GET MY VEHICLE STOPPED. LUCKILY IT'S A 5 SPEED. I GEARED DOWN AS FAST AS I COULD AND MANAGED TO PULL IT OFF THE MAIN ROAD ONTO A HILL TO GET IT STOPPED. AFTER INSPECTING MY VEHICLE I FOUND SEVERE DAMAGE. THE MOTORS MOUNTS ARE BARELY THERE. THE PART WHERE THE FRAME MOUNTS TO THE BODY IS ACTUALLY MISSING ONE DUE TO RUSTING COMPLETELY OUT. EVERY SINGLE BOLT AND NUT IS RUSTED. EVERY SINGLE SQUARE INCH OF THE FRAME IS RUSTED. THE PROBLEM IS THAT JEEP POORLY DESIGNED THE FRAME WITH SIDE HOLES FOR WATER AND DIRT TO ENTER BUT DID NOT DESIGN IT WITH DRAINAGE HOLES ON THE BOTTOM OF THE FRAME. WATER AND DIRT ENTER AND NEVER LEAVE. IT'S EXTREMELY UNSAFE TO DRIVE. I'VE READ THOUSANDS OF COMPLAINTS ONLINE AND THIS IS A VERY COMMON PROBLEM.

HAD TO REPLACE THE FRAME DUE TO LEFT REAR RUSTED THROUGH THE WHOLE FRAME, JUST A SMALL AMOUNT OF THE FRAME WAS LEFT. OTHER AREAS HAD RUST EATING THREW THE FRAME, AND IN A MATTER OF TIME WOULD HAVE FAILED!!!.

"TJ WRANGLER FRAME RUST" - SEVERE RUST OCCURRED IN THE FRAME OF MY 1998 JEEP WRANGLER. VEHICLE WOULD NO LONGER PASS PA STATE INSPECTION. RUST WAS DUE TO NO DRAINAGE HOLE AND FRAME RUSTED FROM INSIDE OUT. RUST OCCURRED ON BOTH DRIVER AND PASSENGER SIDES JUST IN FRONT OF THE REAR CONTROL ARMS AND EXTENDED FRONT TO THE TRANSFER CASE MOUNTING POINTS. I HAVE RESEARCHED THIS ISSUE AND IT IS VERY COMMON AND MANY POOR JEEP OWNERS ARE PARTING OUT PERFECTLY GOOD JEEPS DUE TO THEM NOT BEING ABLE TO PASS STATE INSPECTIONS - LUCKILY NO ONE HAS BEEN HARMED DUE TO THIS FRAME DAMAGE THAT I AM AWARE OF - SOME VIDEOS ON THE INTERNET SHOW THE ENTIRE FRAME RUSTED AWAY! THIS NEEDS TO BE BROUGHT TO THE ATTENTION OF JEEP AS THIS IS OBVIOUS A DESIGN FLAW AND OWNERS SHOULD BE COMPENSATED. IF THERE IS ANY DOUBT OF HOW SEVERE THIS IS SIMPLE DO A GOOGLE SEARCH! TOYOTA TOOK CARE OF THEIR CUSTOMERS!!!

I HAVE AN EXCESSIVE AMOUNT OF FRAME RUST AND MY VEHICLE HAS LESS THAN 150XXX MILES AND THIS IS A SEVERE SAFETY HAZARD. I HAVE READ THAT THERE ARE MANY PEOPLE WHO HAVE EXPERIENCED THIS AND I AM WANTING TO KNOW WHAT YOU GUYS COULD DO TO RESOLVE THIS ISSUE. I BOUGHT THIS VEHICLE AND I DO NOT WANT TO RESALE BECAUSE I DO NOT WANT TO SELL IT IN THIS CONDITION AND I WANT TO KEEP IT BUT I ALSO DO NOT WANT TO DRIVE BECAUSE OF THIS. THERE'S A LOT OF LIFE LEFT IN THIS VEHICLE AND IT ONLY HAS 126XXX MILES SO I NEED HELP

ON MY 1998 JEEP WRANGLER SPORT, CHRYSLER PUT A HOLE IN THE FRAME TO ACCESS THE REAR SWAY ARM BOLT AND WHEN THEY DID THAT IT LET WATER , DIRT, SALT ETC INTO THE FRAME AND CAUSE THE FRAME TO ROT FROM THE INSIDE OUT. I HAVE RESEARCHED THE PROBLEM AND MANY PEOPLE SEEM TO HAVE THE SAME ONE I WANT TO PUT THE WORD OUT TO HAVE IT FIX BECAUSE IF IT WAS TO BREAK WHILE DRIVING YOUR JEEP IT CAN COST SOMEONE THERE LIFE. MINE HAS YET TO DO SO BECAUSE I SEEN IT IN TIME AND WANT SOMETHING DONE ABOUT IT A RECALL IS NEEDED TO FIX THE PROBLEM

TAKATA RECALL REPORTING THIS IN HOPES OF HAVING THE ISSUE RESOLVED BY NHTSA OR CHRYSLER... I HAVE A 1998 JEEP WRANGLER AND LIKE THOUSANDS OF OTHERS, MINE HAS DEVELOPED MAJOR FRAME RUST. I KNOW THIS ISNT GOING TO BE RESOLVED ANYTIME SOON, BUT I NEED TO GET MINE FIXED NOW. HOPEFULLY IF THERE IS EVER A RECALL I CAN STILL BE APART OF IT EVEN AFTER MINE IS REPAIRED. IM GOING TO BE HAVING IT PATCHED FOR NOW AS A FRAME REPLACEMENT WILL COST WAY TOO MUCH FOR ME AT THE MOMENT. MYSELF, ALONG WITH MANY OTHERS WOULD GREATLY BENIFIT FROM THIS BEING RECALLED. THERE ARE A LOT OF JEEPS OUT THERE DRIVING ON REPAIRED FRAMES. THIS ISSUE SHOULD BE RESOLVED BEING AS THERE ARE SO MANY WITH THE EXACT SAME PROBLEM.

SEAT BELTS DO NOT GRAB WHEN PULLED RAPIDLY, MOST OF THE TIME. THE CENTRIFUGAL PAWLS SEEM TO NOT BE FREELY MOVING OUTWARD AND HOLDING THE BELT FROM FREELY PLAYING OUT, WHEN THEY SHOULD. I MADE THE TEST WHILE PARKED WITH ENGINE RUNNING AND OFF, AND ALSO WHILE IN MOTION.

TL* THE CONTACT OWNS A 1998 JEEP WRANGLER. WHILE DRIVING AT AN UNKNOWN SPEED, THE SPEEDOMETER FAILED TO DISPLAY THE SPEED INTERMITTENTLY. THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 124,000.

DESIGN FLAW WHICH ALLOWS WATER IN BUT NOT OUT CAUSES WATER AND DIRT TO COLLECT INSIDE OF CHASSIS FRAME, CAUSING IT TO RUST FROM THE INSIDE OUT.

WHILE USING CRUISE CONTROL SPEED INCREASED AND WOULD NOT RESPOND TO SHUTTING OFF SPEED CONTROL OR BY HITTING THE BRAKES CAR COULD NOT BE STOPPED ONLY PUSHING IN CLUTCH WHILE THE ENGINE RACED UNCONTROLLABLY AND PULLING OFF THE INTERSTATE ONTO SIDE OF ROAD TURNING OFF KEY STOPPED THIS . WHEN STARTED BACK UP ENGINE STILL RACING. SAME THING HAPPENED ABOUT SEVEN YEARS AGO NEVER USED SPEED CONTROL AGAIN UNTIL THIS

THE RUST IS SO BAD ON THE JEEPS IT'S RIDICULOUS IT'S NOT SAFE YOUR GOING TO KILL SOMEONE WHEN THERE REAR AXLE SHOOTS OUT FROM UNDER THEM THIS IS A ISSUE YOU SHOULD FIX NOT THE CONSUMER I WILL NOT BE BUYING THIS PRODUCT AGAIN IF IT IS MY FIXED. 98 TJ JEEP WRANGLER

WHILE REPLACING SHOCKS I FOUND MULTIPLE ROT SPOTS IN THE FRAME OF THE JEEP. THESE ROT SPOTS WERE SO BADLY ROTTED THAT I COULD POKE THROUGH WITH MY INDEX FINGER WITH MINIMAL FORCE. HAD TO SEND IT TO A REPAIR SHOP TO REPAIR THE FRAME IN MULTIPLE LOCATIONS.

DUE TO EXCESSIVE ROT THAT IS COMMON ON THIS VEHICLE, WHILE TRAVELING I HIT A BUMP AND SNAPPED MY DRIVER SIDE CONTROL ARM. THIS CONSEQUENTLY MADE FOR A DANGEROUS RIDE. WHILE ATTEMPTING TO REPAIR IT I NOTICED HOW BAD THE FRAME WAS ROTTED, BUT UNLIKE NORMAL CIRCUMSTANCES WHERE THE OUTSIDE AND INSIDE WOULD HAVE EQUAL CORROSION. THE INSIDE WAS ROTTED MUCH WORSE, AND PARTS OF THE FRAME EASILY CRUMBLED. *TR

THE FRAME AROUND THE CONTROL ARMS ARE RUSTING, THIS COULD BE A SERIOUS PROBLEM THAT NEEDS ADDRESSED AND THERE ARE MORE 97-06 WRANGLERS WITH RUSTED FRAMES THAN NOT. *TR

PURCHASED A USED 1998 JEEP WRANGLER SPORT ON DECEMBER 27 2014. HAD IT IN A SHOP FOR NEW TIRES WHEN THEY TOLD ME THE FRAME WAS ROTTED AND IT WAS UNSAFE TO DRIVE. THE DEALERSHIP I BOUGHT IT FROM INSPECTED IT AND SURE ENOUGH, ROTTED FRAME AND UNSAFE TO DRIVE. THEY AGREED TO PAY 1700 DOLLARS TOWARDS THE COST OF A FRAME SWAP AND IT COST ME 1000 DOLLARS MORE FOR A TOTAL OF 2700 DOLLARS. THIS SEEMS TO BE A REAL ISSUE WITH JEEPS BETWEEN THE YEARS OF 97 TO 04, I MAY BE WRONG ON THE EXACT YEARS BUT THERE IS A DEFINITE PATTERN OF BAD MANUFACTURING PRACTICES/BAD QUALITY STEEL TO BE CONTRIBUTING TO THIS FRAME ROT. IS CHRYSLER WAITING FOR SOMEONE TO GET KILLED IN ORDER TO ADDRESS THIS ISSUE? BIG CORPORATIONS AND POLITICS MEET TO SCREW THE GENERAL PUBLIC ONCE AGAIN? CHRYSLER, TAKE A LESSON FROM TOYOTA AND FIX THESE FRAMES BEFORE SOMEONE GETS KILLED GOING DOWN THE HIGHWAY AT 65 MPH AND THEIR FRAME BREAKS. MY JEEP WAS TOTALLY BONE STOCK WHEN THIS WAS DISCOVERED. I'M NOT TRYING TO GET A DOLLAR BACK FOR WHAT I PAID, JUST TRYING TO BRING AWARENESS TO THIS AS HAVE MANY OTHERS. JEEPERS LOVER THEIR JEEPS NO DOUBT AND ARE VERY LOYAL TO THE BRAND. CHRYSLER SHOULD RECOGNIZE THIS AND DO THE RIGHT THING. I HOPE MANY MORE COME FORWARD AND STEPS ARE TAKEN TO RIGHT THIS WRONG BEFORE SOMEONE GETS KILLED. CHRYSLER CAN BLAME IT ON ROAD SALT OR SEA AIR OR WHATEVER, BUT THERE ARE OTHER AUTO MANUFACTURERS WITH CARS STILL ON THE ROAD FROM THE 60'S AND 70'S AND EARLIER ERAS WITH NO FRAME PROBLEMS AT ALL. BIG CORPORATIONS HIDE BEHIND BAD POLITICS AND THEY WORK HAND IN HAND TO NOT TAKE BLAME FOR THINGS LIKE THIS. ONE OF MANY PROBLEMS WITH POLITICS IN AMERICA. *TR

THE FRAME AROUND THE CONTROL ARMS ARE RUSTING, THIS COULD BE A SERIOUS PROBLEM THAT NEEDS ADDRESSED AND THERE ARE MORE 97-06 WRANGLERS WITH RUSTED FRAMES THAN NOT. *TR

ALL OF A SUDDEN THE SPEEDOMETER AND TACHOMETER GO DEAD, AND THE AIRBAG AND ENGINE LIGHT COME ON. SEEMS TO HAPPEN DURING THE SUMMER MONTHS. I HAVE TO HIT THE DASH A COUPLE OF TIMES AND EVERYTHING STARTS WORKING AGAIN. DOESN'T HAPPEN IN THE WINTER WHEN IT'S COLD. IT'S A LITTLE UNNERVING WHEN THE SPEEDOMETER STOPS WORKING. *TR

I WAS DRIVING AND RUNNING THE HEATER AND NOTICED A BURNING SMELL. I IMMEDIATELY SHUT DOWN THE HVAC UNIT AND SMELL SUBSIDED. I PULLED THE HVAC HEAD UNIT OUT AND HAD A VACUUM LINE AND IT'S INSULATION MELTED. THIS COULD HAVE CAUSED A FIRE. THE HEAT AND AC NOW ONLY WORK ON THE HIGHEST SETTING. *TR

TL* THE CONTACT OWNS A 1998 JEEP WRANGLER. THE CONTACT STATED THAT THE SEAT BELT WAS SECURED AND UPON TAKING THE SEAT BELT OFF IT DID NOT RETRACT AT RANDOM. THE FRONT DRIVERS SEAT SHOULDER BELT TURNING LOOP BECAME STUCK BETWEEN THE DOOR FRAME AND THE SEAT ON MULTIPLE OCCASIONS MAKING IT DIFFICULT FOR THE DOOR TO CLOSE PROPERLY. THE CONTACT HAD TO MANUALLY RETRACT THE SEAT BELT IN ORDER TO CLOSE THE DRIVERS SIDE DOOR. THE SEAT AND METAL FRAMING WAS ALSO WORN. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHO STATED THAT THE CONTACT WAS NOT INCLUDED IN NHTSA CAMPAIGN ID NUMBER:98V048000 (SEAT BELTS) DUE TO THE STATUTE OF THE TIME FRAME FOR THE RECALL REPAIRS. THERE WAS ALSO A LEAK BEHIND THE DASHBOARD THAT HAD LEAKED INTO THE FLOOR MATS ON THE FRONT DRIVERS SIDE AND FRONT PASSENGERS SIDE OF THE VEHICLE. THE AUTHORIZED DEALER WAS NOT ABLE TO REPLICATE THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND PROVIDED NO REMEDY. THE APPROXIMATE FAILURE MILEAGE WAS 200.

NOTICED A NOISE WHILE DRIVING HOME THE OTHER DAY THOUGHT IT MAY HAVE BEEN MY EXHAUST RATTLING AROUND, SO I GOT UNDER VEHICLE TO INSPECT THE NOISE, AND WHAT I FOUND WAS THAT THE REAR PART OF THE FRAME HAS RUSTED AWAY AND THE BRACKETS FOR THE REAR TRAILING ARMS HAD DETACHED FROM THE FRAME ALLOWING THE ARMS TO DROP, AND ON THIS PARTICULAR SIDE THE BRAKE LINES ARE ATTACHED TO THIS CONTROL ARM. I KNOW THAT TOYOTA HAD A SIMILAR RECALL ON THE TRUCK FRAMES FOR RUST PERFORATION, AND THAT JEEP HAD ONE ON THE LIBERTY FOR THE REAR LOWER CONTROL ARMS RUSTING AND BREAKING. I AM AN AUTOMOTIVE TECHNICIAN AND MY PERSONAL JEEP IS NOT THE FIRST ONE I HAVE SEEN WITH THIS POTENTIALLY DANGEROUS CONDITION. I ALSO GOOGLED THIS PROBLEM AND FOUND THAT ITS VERY COMMON IN THESE VEHICLES AS WELL. *TR

REAR DRIVE SHAFT SHEARED IN TWO AT A WELD JOINT LOCATED BETWEEN THE SHAFT MAIN TUBE BODY AND UNIVERSAL JOINT PART. THE FAILURE APPEARS TO BE ASSOCIATED WITH AN IMPROPER WELD SEAM (WELD ON APPARENTLY A THIRD OF THE CIRCUMFERENCE OF THE SHAFT TUBE APPEARS NOT TO HAVE BEEN COMPLETED). I DON'T KNOW IF THE WELDING PROCESS WAS DONE MANUALLY OR BY MACHINE AND IF BY MACHINE HOW MANY OTHER SHAFTS ARE SIMILARLY AFFECTED. I WILL MAIL A MORE COMPLETE COPY OF A WRITE-UP OF THE INCIDENT AS WELL AS PHOTOGRAPHS (I SENT CHRYSLER. I CONTACTED CHRYSLER AND THEY HAVE NOT FOLLOWED UP ON THE INCIDENT (OTHER THAN A VOICE MAIL ACKNOWLEDGING RECEIPT OF A LETTER FROM ME AND THEY WOULD LOOK INTO THE MATTER. THAT HAS BEEN CLOSE TO 5 MONTHS OF NO RESPONSE.

THE FRAME IS ROTTEN OUT, AND THIS IS A COMMON PROBLEM WITH THE JEEP TJ'S. I HAVE A HOLE ON MY TAIL SECTION OF FRAME AND ON THE REAR CONTROL ARM AREA. *TR

WAS TOLD BY MY MECHANIC FRAME IS RUSTING FROM THE INSIDE OUT, AND THE FRAME WILL FAIL IN THE NEAR FUTURE. I UNDERSTAND THIS IS A ON GOING PROBLEM WITH JEEP WRANGLERS OF MULTIPLE YEARS DUE TO THE FACT THERE WERE NEVER DRAIN HOLES PROVIDING DRAINAGE FOR THE WATER, ALSO LACK OF ANY RUST COATING TO THE INSIDE OF FRAME. IN PENN. YOU CAN NOT SELL A CAR WITH FRAME DAMAGE. I'M NOT SURE WHAT I'M GOING TO DO.I FEEL THAT JEEP SHOULD HELP WITH THE REPAIR OR REPLACEMENT OF THE FRAME. *TR

I HAVE HAD NUMEROUS TIMES THAT MY GAUGES JUST STOP WORKING AND THEN ONE DAY I WENT TO DRIVE IT AND I HAD NO TURN SIGNALS OR BRAKE LIGHTS. IT IS IN THE MECHANIC SHOP AS WE SPEAK. THEY HAVE FOUND THE ELECTRICAL CONNECTOR UNDER THE LEFT SIDE OF THE DASH HAS COMPLETELY MELTED AND ALL THE WIRES HAVE FUSED TOGETHER. I WAS VERY LUCKY THAT IT DIDN'T CATCH ON FIRE. NOW THE OTHER PROBLEM IS FINDING THE PART MY MECHANIC HAS TRIED EVERYWHERE TO FIN IT. SO NOW MY JEEP IS JUST SITTING IN THE SHOP GOING ON THREE DAYS NOW UNTIL A PART CAN BE FOUND. WHY IS THERE NO RECALL ON THIS AS I SEE ON HERE AND OTHER SITES THAT IT IS DANGEROUS AND MANY HAVE HAD THE SAME ISSUES?? *TR

DEATH WOBBLE, FRONT END SHAKES VIOLENTLY AT HIGHER FREEWAY SPEEDS. VERY FEARFUL TO DRIVE ON OTHER THAN STREETS. HAS HAPPENED SEVERAL TIMES THE LAST 2 YEARS. PURCHASED JEEP USED 5 YEARS AGO BUT ONLY STARTED TO HAVE WOBBLE LAST 2 YEARS SINCE IM RETIRED AND DON'T DRIVE LONG DISTANCES VERY OFTEN AND NOT DON'T WANT TO DRIVE ANYWHERE THAT REQUIRES ME TO USE FREEWAYS. *TR

JEEP DEATH WOBBLE. SCARY! *TR

MY SON WAS KILLED WHEN THE 98 JEEP WRANGLER LOST CONTROL AND FLIPPED. THE AIR BAGS DID NOT DEPLOY. I HAVE NOTICED THAT THIS HAS BEEN AN ISSUE SINCE THIS VEHICLE WAS BUILT IN 1998. MANY COMPLAINTS SINCE THE YEAR OF 1998 AND NO RECALL OR FIX? *TR

Crash 1 deaths

RUST HAS EATEN COMPLETELY THROUGH JEEP FRAME IN REAR SUPPORT AREA THROUGH ABOUT MIDWAY OF THE DOOR SECTION. THIS IS NOT MINOR SURFACE RUST, BUT LARGE GAPING HOLES THAT I CAN PUT MY WHOLE HAND INSIDE OF. THE JEEP WAS PURCHASED NEW IN 1998 AND HAS NEVER BEEN OFFROAD. IT HAS VERY LOW HIGHWAY MILEAGE AND IS IN AN AREA WHERE THE WINTERS ARE MILD, SO THERE'S NOT A LOT OF ROAD SALT USED DURING THE WINTERS HERE. IT HAS BEEN MAINTAINED AND HAS BEEN WELL TAKEN CARE OF. I HAD RECENTLY TAKEN IT TO A FABRICATION SHOP TO SEE IF IT COULD BE REPAIRED, AND AFTER EXAMINATION THE SHOP OWNER SAID THERE IS NO SOLID METAL LEFT IN THE FRAME FOR A REPAIR TO BE POSSIBLE. HE SAID THERE ARE NO DRAIN HOLES ON BOTTOM OF THE JEEP FRAME, BUT ONLY HOLES THAT THE MANUFACTURER PUT ON THE SIDE OF THE FRAME. HE SAID, AS A RESULT ROAD GRIME ENTERED THE FRAME FROM THESE MANUFACTURED SIDE HOLES, GOT TRAPPED INSIDE THE FRAME AND CAUSED IT TO RUST FROM THE INSIDE OUT. HE SAID THAT IS WHY I HAD NOT DETECTED THE SEVERITY OF THE RUST PROBLEM BEFORE NOW. THE SHOP OWNER PUT HIS HAND INSIDE THE FRAME AND PULLED OUT A HANDFUL OF MOIST ROAD GRIME AND LOOSE RUST FLAKES TO FURTHER ILLUSTRATE THE PROBLEM. THE SHOP OWNER WENT ON TO INFORM ME THAT MY JEEP IS NOT SAFE TO DRIVE. IN STARK CONTRAST, THE UNDERSIDE OF THE BODY OF THE JEEP HAS ABSOLUTELY NO RUST AT ALL. *TR

TL* THE CONTACT OWNS A 1998 JEEP WRANGLER. WHILE PARKED, THE CONTACT HEARD AN ABNORMAL SOUND FROM THE SIDE OF THE ENGINE, AS IF AIR WAS ESCAPING THROUGH THE ENGINE. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING WHERE THE TECHNICIAN STATED THAT THE EXHAUST MANIFOLD WAS FRACTURED AND WOULD HAVE TO BE REPLACED. THE FAILURE RECURRED AFTER THE REPAIR. THE VEHICLE WAS REPAIRED A SECOND TIME. THE APPROXIMATE FAILURE MILEAGE WAS 87,000.

TL* THE CONTACT OWNS A 1998 JEEP WRANGLER. WHILE DRIVING APPROXIMATELY 15 MPH, THE CONTACT HEARD A LOUD RATTLING NOISE UNDERNEATH THE VEHICLE. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHERE THE CATALYTIC CONVERTER WAS REPLACED. RECENTLY, THE CONTACT DISCOVERED A VOLUNTARY RECALL ISSUED BY THE MANUFACTURER PERTAINING TO THE POWER TRAIN CONTROL MODULE. THE CONTACT WAS DISPLEASED TO KNOW THE VIN WAS NOT INCLUDED IN THE RECALL AND INELIGIBLE FOR REIMBURSEMENT FOR THE PRIOR REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 95,000. THE CONSUMER STATED THE EXHAUST MANIFOLD CRACKED ON TWO SEPARATE OCCASIONS AND HAD TO BE REPLACED.

PURCHASED MY JEEP NEW IN 1998 AND I ONLY DROVE IT ABOUT 5000 MILES PER YEAR..IN ABOUT 2009 I BEGAN TO HAVE SOME TROUBLE WITH THE GAUGES/SPEEDOMETER..THEY WOULD STOP FUNCTIONING FOR PERIODS OF TIME...IN ABOUT 2010 I THERE WAS AN ODOR COMING FROM THE VENTS WHEN I USED MY HEATER OR AC..EACH TIME I TOOK IT TO THE DEALER WHERE I PURCHASED THE VEHICLE AND THE LAST TIME I HAD IT CHECKED WAS THE END OF SEPTEMBER 2011. ON NOVEMBER 21, 2011 I WAS DRIVING TO THE GROCERY STORE WITH THE HEATER ON AND SMOKE STARTED COMING OUT OF THE VENTS..I TURNED OFF THE HEATER & BLOWER & THEN SAW FIRE COMING OUT FROM UNDER THE DASH ON THE PASSENGER SIDE. I STOPPED & TRIED TO PUT OUT THE FLAMES WITH MY JACKET. A LADY STOPPED TO HELP & CALLED 911. WHILE WAITING FOR THE FIRE DEPARTMENT (JUST A FEW MINUTES) AND I WAS SITTING IN THE LADY'S CAR...I WATCHED MY JEEP START MOVING TO THE RIGHT (EVEN THOUGH THE IGNITION WAS TURNED OFF & THE JEEP WAS IN GEAR)...IT WENT INTO A GRASS FIELD, BURST INTO FLAMES AND WAS A TOTAL LOSS. I ONLY HAD MINOR BURNS ON MY FINGERS & HANDS (FROM TRYING TO PUT OUT THE FIRE). I AM EXTREMELY UPSET! *TR

Fire 1 injured