2013 FORD EXPLORER Recalls, Complaints & Safety

The contact owns a 2013 Ford Explorer. The contact stated that while driving approximately 65 MPH, the driver's side A-pillar trim was blown off the vehicle. The contact was unable to recover the trim. The contact stated that much later, while the vehicle was with the dealer, the dealer informed the contact that the passenger’s side A-pillar trim was loose, and tape was used to secure the trim in place. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part was not yet available. The dealer and the manufacturer were asked about parts availability and were informed that owners would be notified by mail when parts were available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 120,000.

See attached document for complaint.

this recall has been active since 2023. I was told a remedy would be available ladder 2024…. I received another letter in September 2025 reminding me of the recall and it is now March 2026 with no current remedy available. This vehicle was used for my work vehicle and I am no longer able to use it to make income due to it having a recall. This has been a major problem. These parts also seem to be available by third-party online looking for help or suggestions. Not sure what to do at this point. Thanks!

The rear reverse camera malfunctions and glitches. Often the screen turning green when reversing, sometimes screen is black or no color view and most times the camera if reversing to left or appear as to the right or vise versa and sometimes it’s normal but rarely. The control buttons for windows has a malfunction where it sometimes works and sometimes doesn’t. The seatbelts are not clicking and I have kids in the rear seats.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was contacted, but the vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the A-pillar trim was detached from the driver’s and passenger’s side windshields. The approximate failure mileage was 217,000

While driving a 2013 Ford Explorer, the vehicle experienced an electrical issue that caused the power steering system to malfunction. The power steering assist suddenly failed, making the steering wheel extremely difficult to turn. The failure occurred suddenly and at the time of the incident the vehicle was traveling 2 miles and I parked it immediately.This created a serious safety hazard, especially when attempting to turn or maneuver the vehicle. A warning message stating “Power Steering Assist Fault” did appear on the dashboard .Prior to the failure, there were no warning signs. Due to the sudden loss of power steering assist, the driver’s ability to safely control the vehicle was significantly reduced, increasing the risk of a crash. The issue has not yet been inspected. The vehicle is available for inspection upon request.

My vehicles exterior A-pillar trim is coming off and pieces flew off on highway. I was told to contact Ford.

While driving a 2013 Ford Explorer, the vehicle experienced an electrical issue that caused the power steering system to malfunction. The power steering assist suddenly failed, making the steering wheel extremely difficult to turn. The failure occurred suddenly and at the time of the incident the vehicle was traveling 2 miles and I parked it immediately.This created a serious safety hazard, especially when attempting to turn or maneuver the vehicle. A warning message stating “Power Steering Assist Fault” did appear on the dashboard .Prior to the failure, there were no warning signs. Due to the sudden loss of power steering assist, the driver’s ability to safely control the vehicle was significantly reduced, increasing the risk of a crash. The issue has not yet been inspected. The vehicle is available for inspection upon request.

Review camera unavailable, image flashing, or image reversed.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The contact stated that while driving at an undisclosed speed, the driver's and the passenger's side A-pillar trims were loose. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.

My car was parked in the driveway and it caught on fire from under the hood.

Fire

The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the steering wheel seized, with the power steering warning light illuminated. The contact stated that the steering wheel became difficult to turn. The vehicle was taken to an independent mechanic, but the vehicle was not diagnosed or repaired. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 201,226.

My backup camera is in reverse. When I use it everything is on the incorrect side which is a safety issue when backing up.

The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the driver's side exterior A-pillar trim detached and struck another vehicle. No warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was taken back to the residence. Several dealers were contacted and confirmed that the part was not yet available. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 146,000.

This is a complaint regarding the handling of safety recall 20S62 (also referenced as 20S32) by Ford Motors and the dealership that performed the recall repairs, Hallada Motors. The vehicle was taken by the previous owner to Hallada 3 separate times to address the same recall related to the rear suspension toe link/ball joint issue. Documentation indicates the most recent repair occurring in 2022. This recall specifically involves components connected to the rear suspension that, if not properly addressed, can lead to corrosion and structural damage affecting the frame. Based on the history of repeated recall repairs and the current condition of the vehicle, we believe that the repair approach taken was insufficient. By the time of the third recall service in 2022, the frame should have been thoroughly inspected and potentially replaced due to corrosion risk identified in the recall guidance. The vehicle is currently being inspected and serviced at Ewald Ford. Their technicians documented significant corrosion and unusual frame damage, which they photographed and submitted to Ford corporate while requesting that the recall case be reopened. Despite this documentation, Ford has refused to reopen the recall or authorize a frame replacement. Ewald Ford technicians noticed irregularities in the documentation from Hallada Motors. 2 separate entries list the mileage as exactly 87,600 miles and exactly 95,000 miles, both ending in multiple zeros. The technicians indicated this is unusual and raised concerns whether the recall work was properly completed. The vehicle now has severe frame corrosion and structural damage and is unsafe and unusable. We are without a vehicle and have incurred financial loss. We believe the current condition is the result of improper/incomplete recall repairs. We request a look at the recall repairs performed were completed in compliance & ford's refusal to reopen is consistent with safety obligations. Ford should be held accountable.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that while driving 60 MPH, the passenger's side A-pillar trim detached from the vehicle. The local dealer was contacted and confirmed that the part for the recall repair was not available. The dealer used black tape as an interim repair. The contact became aware that the seal around the front passenger’s side windshield had started to deteriorate. Recently, the contact noticed small amounts of water occasionally leaking inside the vehicle from the front passenger’s side windshield. The vehicle was not repaired after the most recent failure. The contact stated that the driver’s side A-pillar trim was loose. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue, and no assistance was offered. The manufacturer informed the contact that the seal and leak were symptoms of the recall, but not related to the recall, and therefore not covered under the recall. The failure mileage was unknown.

I am submitting a formal safety complaint regarding a severe design defect in the 3.5L V6 engine of my 2013 Ford Explorer. The vehicle is equipped with an internal, chain-driven water pump that is currently failing at 100000 miles, as evidenced by coolant actively draining from the factory weep hole. Because this pump is located inside the engine block and driven by the timing chain, a complete seal failure dumps engine coolant directly into the oil pan. This is a critical safety hazard. When the coolant and oil mix, it destroys the engine bearings and causes the engine to completely seize without warning. If this sudden engine seizure occurs while driving at highway speeds, it results in an immediate and total loss of motive power, power steering, and power brakes. This defect creates an extreme crash hazard for the occupants of the vehicle and other drivers on the road. The internal weep hole provides virtually no dashboard warning or indicator to the driver before this catastrophic failure occurs. I am requesting that the NHTSA investigate this known, dangerous design flaw to force a mandatory safety recall before this sudden loss of vehicle control causes severe injuries or fatalities.

The contact owns a 2013 Ford Explorer. The contact stated that the trim along the front windshield had become loose, and the lining was pushed outward and was partially missing and detached. The contact was concerned that the windshield could potentially loosen or fall out due to the failure. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure). The local dealer was contacted and confirmed that parts were on back order. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was unknown.

I am submitting a formal safety complaint regarding a severe design defect in the 3.5L V6 engine of my 2013 Ford Explorer. The vehicle is equipped with an internal, chain-driven water pump that is currently failing at 100000 miles, as evidenced by coolant actively draining from the factory weep hole. Because this pump is located inside the engine block and driven by the timing chain, a complete seal failure dumps engine coolant directly into the oil pan. This is a critical safety hazard. When the coolant and oil mix, it destroys the engine bearings and causes the engine to completely seize without warning. If this sudden engine seizure occurs while driving at highway speeds, it results in an immediate and total loss of motive power, power steering, and power brakes. This defect creates an extreme crash hazard for the occupants of the vehicle and other drivers on the road. The internal weep hole provides virtually no dashboard warning or indicator to the driver before this catastrophic failure occurs. I am requesting that the NHTSA investigate this known, dangerous design flaw to force a mandatory safety recall before this sudden loss of vehicle control causes severe injuries or fatalities.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that while driving rounding a corner at a slow speed, the front passenger’s side A-pillar trim detached and separated from the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The vehicle was not repaired. The failure mileage was approximately 150,000.

I am filing a safety complaint for my 2013 Ford Explorer (VIN: [XXX] ). There is a strong raw fuel smell inside the cabin, which is a severe fire hazard. This model has a history of cracked fuel delivery modules. Additionally, my vehicle has open recalls for the Rear Suspension Toe Link (19V435/20V675) and the A-Pillar Exterior Trim (24V031). Despite these critical safety issues, the dealer (Midland Ford) claims they see no open recalls and refuses to inspect the fuel leak without a diagnostic fee. I am concerned about a potential fire and the risk of a suspension failure while driving." INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that a technician went to the residence and diagnosed and determined that the A-pillar trim on both sides of the windshield had failed and needed to be replaced. The dealer confirmed that parts were not yet available. The vehicle was not repaired. The dealer applied duct tape to both sides of the windshield as a temporary fix. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The approximate failure mileage was 161,708.

After dropping off my son at school, I turned the steering and suddenly it became very difficult to turn. I was stuck in school traffic and was nearly involved in an accident. Shortly after , the power steering assist warning light came on. I brought the vehicle to my mechanic, who ran a diagnostic and informed me there is a known recall related to the steering system on 2013 Ford Explorers. Based on this, the vehicle was towed by AAA to the nearest Ford Dealership. At the dealership, I was told that my specific Vehicle ( VIN#) is not listed under the recall. Given the seriousness of the steering failure and the safety risk involved, I am requesting further review and guidance on how to proceed.

Both pilars flew off, right and left. There is a recall and i went to Ford in San Bruno and Fullerton, both were giving me the run around and supposedly in late 2024 parts were available and its now 2026 and i am still waiting for both to be replaced. I need this case to be expedited from Ford. Thank you

The contact owns a 2013 Ford Explorer. While driving approximately 70 MPH, the passenger’s side A-pillar trim was blown off the vehicle by the slipstream. The dealer was not contacted because the contact had previously called the dealer and was informed that the part to repair the vehicle was not available. The VIN was included in NHTSA Campaign Number: 24V031000 (STRUCTURE). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 145,000.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure). The contact stated that while driving at an undisclosed speed, there was wind constantly entering the vehicle from the front passenger’s side of the windshield. The contact inspected the vehicle and became aware that the exterior A-pillar trim on the front passenger’s side was missing. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 80,000.

The contact owns a 2013 Ford Explorer. The contact stated that the vehicle was taken to the dealer for a recall repair related to a possible rear suspension toe link fracture. The contact stated that while his son was driving 55 MPH, a month and half after the recall repair, the rear driver's side tire had a blowout, causing the vehicle to swerve and to drift into another lane. The contact stated that there was no oncoming traffic during the failure. The driver was able to pull over to the right side of the road. The contact then met his son on the side of the road, and the contact replaced the rear driver's side tire with the spare tire. The contact then drove to the residence and inspected the tire. The contact noticed that the inner side edge of both rear tires were prematurely worn. The contact related the failure to the recall repair. The dealer was notified of the failure, but no assistance was provided. The vehicle was not diagnosed or repaired. Landmark Ford, Inc. (2401 Prairie Crossing Dr, Springfield, IL 62711); was contacted and the contact was informed that the previous dealer did not complete the alignment during the recall repair, causing the premature wear of the tires. The manufacturer was notified of the failure, and a case was filed. The failure mileage was approximately 248,995.

The contact owns a 2013 Ford Explorer. The contact stated that the vehicle was purchased in late 2024, and approximately six months later, the rearview camera failed. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The message "Rear Camera Unavailable - Contact your Dealer" was displayed. The local dealer was contacted and referred the contact to the NHTSA Hotline for assistance. The vehicle was not repaired. The manufacturer was not made aware of the issue. The failure mileage was 75,000.

The contact owns a 2013 Ford Explorer. The contact stated that the ABS, the brakes, and the traction control warning lights were illuminated. The vehicle was taken to the dealer, where it was diagnosed that the ABS module had failed and needed to be replaced. The dealer initially informed the contact that the part was on backorder. The vehicle was not repaired. The contact was later informed that the part had been discontinued. The manufacturer was not notified of the failure. The failure mileage was approximately 147,719.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000(Structure); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not available. The contact stated that the passenger's side and driver's side windshield exterior A- Pillar trims had detached from the vehicle. The contact replaced the trims with aftermarket parts; however, the failure reoccurred. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 178,000.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the recall remedy parts were not fully available. The local dealer was contacted and confirmed that the recall remedy was partially available. The dealer stated that the driver-side A-pillar trim was available, but the passenger-side A-pillar trim was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue, and a case was filed. The contact had not experienced a failure.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that upon further inspection, the contact noticed that the front passenger’s side A-Pillar trims had become loosened. Two local dealers were contacted on various occasions, including McGovern Ford of Lowell (1212 Westford St, Lowell, MA 01851). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 65,000.

Hi, my power steering went out. It's tough to turn. I see there was a safety recall, 14S06, that mentions the power steering control module. According to the NHTSA website my car has a safety recall. MAY 29, 2014 NHTSA CAMPAIGN NUMBER: 14V286000 Loss of Electric Power Steering Assist If the vehicle experiences a loss of power steering assist it will require extra steering effort at lower speeds, increasing the risk of a vehicle crash.

I was leaving the store pulled out on a main road in town about to head on the highway. My steering wheel locked and would hardly move with all my strength and the help of my significant other we pulled back into the store parking lot rarely missing hitting several vehicles in the process. I had my children with me at the time in this vehicle as well. The power steering assist fault message popped up. I had the vehicle towed to Ford Groves and after a diagnostic test was ran I was told it was my steering gear and the entire steering column needed to be replaced. The second opinion I got said it was the rack and pinion needing to be replaced. After doing research I found other reports of other 2013 ford explorer owners having wrecks due to this some with the same edition as myself (limited). There are recalls for the steering on 2013 ford explorer but not the limited. I need my edition to be added because this is clearly happening here as well. This was very dangerous when I explained to the dealership about the recalls they told me this was not accurate and was the wrong information. This was random and happened out of no where my vehicle was fine prior to this. Yes the vehicle is available upon request for inspection

To Whom it may concern, In February 2025 I was notified by Ford Motor Co. that there's been a recall on my 2013 Ford Explorer Manufacturer recall #24S02 and NHTSA recall #24V031. It also stated that I would be receiving another letter later in the year advising me to contact my dealer to make an appointment to have the recall problem fixed. I received another letter in September of this year advising me to contact my Ford dealer to make an appointment to get this recall fixed. I contacted my Ford dealer and they advised me that they have not received the parts yet and they didn't know when the parts would be arriving. Don't you think that Ford has had enough time to get this recall situation corrected ? They've known about this problem since 2023, and other than sending out a letter advising us of the recall, have done nothing to correct the problem, if in fact there really is one.

My 2013 White Four door Ford Explorer incidents occurred twice on the highway. The end pieces of the front windshield came off while driving on Hwy. 70 in Durham/Raleigh NC and on hwy somewhere in Raleigh! There was a Sherriff behind me the first time. My concern is the wind noise in my vehicle while driving and safety of the windshield for safety inspection. Crossroads Ford in Wake Forest NC service told me that it can take up to 30-60 days to get the parts for my 2013 Ford. I am disabled and I need my vehicle to be safe for doctor visits. Can the new parts be expedited or no?

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the windshield exterior A-pillar trims had become loosened, and water entered the vehicle through the interior light near the rearview mirror. The vehicle was taken to the dealer, where tape was applied to the trim pieces. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 140,000.

The contact owns 2013 Ford Explorer. The contact stated that after starting the vehicle and shifting into reverse(R), the image on the screen was fuzzy. The message “Rearview Camera not Available” was displayed. Neither the dealer nor an independent mechanic was contacted. The vehicle was not taken to a dealer or an independent mechanic to be diagnosed. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 25V695000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The manufacturer was notified of the failure but offered no assistance. The failure mileage was 101,000.

Rear camera on 2013 Ford Explorer has stopped working. There is a safety recall for models beginning with 2015. This is just as much of a safety hazard with the 2013 model as with the 2015 model. Why are all Ford Explorers with this issue not covered by the recall?

Backup camera doesn't always work. It displays a black screen alot of times.