2026 FORD BRONCO

7 recalls, 9 complaints

ENGINE

Defect Description

Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.

Consequence

A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.

Remedy

Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will n... Read more

565,691 vehicles affected

Manufacturer: Ford Motor Company

STRUCTURE:BODY

Defect Description

Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.

Consequence

A detached fender flare can become a road hazard and increase the risk of a crash.

Remedy

Dealers will inspect and repair, or replace the fender flares as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 11, 2026. Additional letters will be sent once the remedy is available, anticipated in late August 2026. Owners may contact Ford custo... Read more

36,046 vehicles affected

Manufacturer: Ford Motor Company

ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL

Defect Description

Ford Motor Company (Ford) is recalling certain 2025-2026 Explorer, Ranger, and Bronco vehicles. The engine may fail, which can result in a loss of drive power.

Consequence

A sudden loss of drive power can increase the risk of a crash.

Remedy

Dealers will replace the engine long block, free of charge. Interim letters, notifying owners of the safety risk, were mailed June 5, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's ... Read more

1,536 vehicles affected

Manufacturer: Ford Motor Company

EQUIPMENT:OTHER:LABELS

Defect Description

Ford Motor Company (Ford) is recalling certain 2026 Ranger and Bronco vehicles. The vehicle specifications listed on the tire placard and safety certification labels may be incorrect, including the VIN, capacity weight, seating capacity, front and rear gross axle weight rating (GAWR), tire and rim d... Read more

Consequence

The incorrect tire size, tire pressures, and GAWR listed on the labels can allow the vehicle to be overloaded or have improperly inflated tires, increasing the risk of a crash.

Remedy

Dealers will inspect and if necessary, replace the certification and TREAD labels, free of charge. Owner notification letters were mailed June 3, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C24. Vehicle Identification Numbers (VINs) involved ... Read more

268 vehicles affected

Manufacturer: Ford Motor Company

SEATS:CRITICAL FASTENERS

Defect Description

Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger and Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.

Consequence

A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.

Remedy

Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed May 22, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford’s number for this recall is 26S30. Vehicle Identification Numbers (VINs) involved in this r... Read more

179,698 vehicles affected

Manufacturer: Ford Motor Company

BACK OVER PREVENTION:SOFTWARE

Defect Description

Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.

Consequence

A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.

Remedy

The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) inv... Read more

849,310 vehicles affected

Manufacturer: Ford Motor Company

ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL

Defect Description

Ford Motor Company (Ford) is recalling certain 2025-2026 Bronco and Bronco Sport vehicles. The Instrument Panel Cluster (IPC) may fail at startup.

Consequence

An instrument panel display that does not show critical information, such as warning lights or vehicle speed, increases the risk of a crash.

Remedy

The instrument panel cluster software will be updated by a dealer or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed December 4, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SC3.

229,609 vehicles affected

Manufacturer: Ford Motor Company

Complaint Statistics

9 total complaints 1 crashes 1 injuries

Top Reported Components

Component	Complaints
UNKNOWN OR OTHER	2
ELECTRICAL SYSTEM	1
ENGINE AND ENGINE COOLING	1
FUEL/PROPULSION SYSTEM	1
VISIBILITY/WIPER	1
SEAT BELTS	1
STRUCTURE:BODY	1
VISIBILITY	1

Incident date: Sep 2, 2026

The contact owns a 2026 Ford Bronco. The contact stated that while driving approximately 70-75 MPH in the left lane on the interstate on a sunny day, near the grass, the driver's side rear window exploded without impact. The local dealer was contacted, but the vehicle was not diagnosed or repaired. ... Read more

Incident date: Aug 29, 2026

While driving on the roadway at approximately 5,841 odometer miles, the vehicle's fender moulding/flare clip retention failed, causing the moulding to loosen and completely detach from the vehicle. The detached fender moulding separated in transit, creating an immediate road debris hazard for surr... Read more

Incident date: Aug 13, 2026

Seat beat created a laceration on arm with normal use.

Incident date: Jul 13, 2026

Constant jerking and shuttering when accelerating/shifting gears. Oil consumption done last year as dealership thought it was engine related. Engine replaced. Problem continues. Fuel in MAP sensor. Continued shuttering at acceleration, shuttering at parked idle, shuttering at braking idle, engine st... Read more

Incident date: May 19, 2026

Vehicle: 2024 Toyota Tundra Double Cab | VIN: [XXX] | Mileage: ~19,200 No crash or injury has occurred. This report concerns an unresolved safety defect. My Tundra intermittently fails to accelerate when the gas pedal is pressed from a slow roll (3-18 mph). The engine revs but the vehicle does not ... Read more

Incident date: May 19, 2026

The contact owns a 2019 Jeep Cherokee. The contact stated that while driving approximately 65 MPH, the vehicle suddenly lost motive power following a loud screeching sound. The Check Engine warning light illuminated, and the vehicle started to misfire upon depression of the accelerator pedal. The co... Read more

Incident date: May 19, 2026

NTHSA recall # 25V467 It has been a year since this recall was issued and still no remedy for fuel injection cracks that can leak fuel onto the engine. How much longer should I have to wait for a remedy?

Incident date: Apr 3, 2026

The 2026 Ford Bronco Outer Banks instrument cluster has gone blank on two occasions (4/3/26 and 4/23/29). The first time the service department at Joe Mahan Ford, Paris, TN reported the display returned when connected to thier computer, but kept the Bronco for several days trying to replicate the co... Read more

Incident date: Apr 15, 2026

2018 Subaru Crosstrek rapidly accelerated unexpectedly while pulling into a parking space with the foot on the brake. Hit a concrete pole and sustained vehicle damage and injuries.

Crash 1 injured

NHTSA Safety Investigations, FORD BRONCO

Investigations opened by NHTSA into potential safety defects. These are separate from recalls and may or may not result in a recall.

PE, Closed , Model Year: 2021

Low-pressure fuel pump failure

On July 29, 2024, the Oﬃce of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with ... no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the aﬀected vehicles may lose fuel pressure and ﬂow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford ﬁled recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identiﬁcation Number document, go to NHTSA.gov.Read more

EA, Closed , Model Year: 2021

Loss of Motive Power

On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporti... ng sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.Read more

PE, Closed , Model Year: 2021

Loss of motive power due to valve intake failure on Ford Bronco vehicles.

The Office of Defects Investigation (ODI) received a petition dated March 16, 2022, requesting an investigation regarding allegations of defective intake valves in model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost (“Nano”) engines. The petitioner alleged these vehicles... Read more

DP, Closed , Model Year: 2021

Loss of Motive Power

The Office of Defects Investigation (ODI) received three petitions on March 17, March 18, and March 29, 2022, which requested a defect investigation into an alleged defect of the valves on model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost engines. The petitioners alleged tha... Read more

EA, Closed , Model Year: 1994

ENGINE COMPARTMENT FIRES

EA05-005 IS CLOSED WITH FORD?S ACTIONS IN RECALLS 05V-017, 05V-388, AND 06V-286, RECALLING APPROXIMATELY 6.7 MILLION VEHICLES EQUIPPED WITH TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCHES (SCDS).THE BRAKE SYSTEMS IN THESE RECALLED VEHICLES GENERATE A VACUUM THAT CAN POTENTIALLY CAUSE THE SCDS ... Read more

RQ, Closed , Model Year: 1992

PARKING BRAKE