2019 HYUNDAI VELOSTER Recalls, Complaints & Safety

I started to hear a grinding sound when breaking and I took it into a Meineke dealer to see about getting it fixed. During a general diagnostic they discovered that 3 of the four brakes were not working and the calipers needed replaced. I was told this was due to a manufacturer issue and that there will be a recall on these parts soon but no ETA. They informed me that they have seen this similar issue on many 2019 Hyundai Velosters and there would be a recall soon but I have no ETA and I cannot drive my vehicle.

Engine locked on me during driving almost caused a car rear ending me during rush hour. Called AAA and they printed out a recall form for over heated piston that may cause engine damage. Towed to Tito Auto care and then printed out the same information for recall details NHTSA Campaign Number 21V301000. Advised me to take to Hyundai dealership to repair for free. Hyundai states the vendor number is not pulling up for a recall. Both AAA and Tito Autocare stated they would fight this. I am requesting you order the Hyundai Manufaturer to repair. I believe there were missed vin numbers in the recall including my vin number.

The contact owns a 2019 Hyundai Veloster. The contact stated that while attempting to accelerate, the vehicle failed to respond with the check engine warning light illuminated. The vehicle was taken to a local dealer where the vehicle was diagnosed, and the contact was informed that the engine was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 120,000.

Attempted to pull out of our neighborhood and car check engine light as well as every other light came on on the dashboard. Car completely loss power and stalled in the middle of the road. Multiple attempts to re-start the car but would not start. Had mechanic check vehicle, originally pulled a code for fuel pump but when tested a few days later and at the fuel pump that code was gone. Checked everything could not find a reason it would not start. Called the Hyundai dealership and they said yeah your engine lost compression and probably has to be replaced but we can't tell you for sure until you bring it in and it will be $350 to tell you if that is the problem. I am having it taken in to see. The car VIN does not show as part of the 21V 301 recall on this site but is experiencing the exact issues listed in the recall. We will see...

This car was recalled for a bad engine and because their computer would not throw off a code they refused to replace the bad engine. It has 60000 miles on it and has been well maintained. The rocker arms have gone bad and there are countless others who have the same issue that Hyundai refuses to address because now computer code was thrown off. They hide behind this to avoid replacing their bad engines.

The contact owns a 2019 Hyundai Veloster. The contact stated that upon starting the vehicle, the check engine warning light illuminated. The contact stated that the failure was intermittent. The vehicle was taken to an independent mechanic, who referred the contact to the dealer for assistance. An unknown dealer was notified of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 57,000.

The contact owns a 2019 Hyundai Veloster. The contact stated that on several occasions while the vehicle was parked in extremely cold weather, the driver’s side door failed to open or close as needed. The vehicle was taken to a dealer where it was diagnosed and determined that the door actuator needed to be replaced. The vehicle was repaired but the failure reoccurred a year later. The manufacturer was notified of the failure. The failure mileage was approximately 40,000.

The contact owns a 2019 Hyundai Veloster. The contact stated that while driving 76 MPH, the vehicle went into LIMP Mode and decelerated to 30 MPH. The check engine warning light was illuminated. Additionally, the vehicle experienced intermittent, unintended acceleration. The contact shifted the transmission to neutral(N), but the vehicle failed to stop. The contact then pressed the shift lock release button, and the vehicle was able to stop. The steering wheel also inadvertently turned left or right while driving, and the Lane Keep Assist System was not activated. The vehicle was taken to the dealer, where it was diagnosed that fuel and oil were leaking into the exhaust pipe, allowing smoke into the cabin. The dealer replaced the alternator, battery, and spark plugs, but the failure persisted. The dealer notified the manufacturer about the failure. The vehicle was then taken to Tarr Hyundai (5524 W Andrew Johnson Hwy, Morristown, TN 37814); however, the dealer was initially unable to duplicate the failure. When Tarr Hyundai was able to duplicate the failure, the failure information was forwarded to the manufacturer. The vehicle was not repaired. The manufacturer was made aware of the failure and several cases were opened. The final case was resolved through arbitration, and the manufacturer was ordered to buy back the vehicle; however, the contact declined the buyback offer. The failure mileage was approximately 141.

When you put the car in DRIVE it will go in REVERSE. Happened several times and on the last time caused us to back into a pole and mess up the back bumper. We were trying to go forward but went in reverse. We have video proof but I can't load the video in this document.

Crash

When you put the car in DRIVE it will go in REVERSE. Happened several times and on the last time caused us to back into a pole and mess up the back bumper. We were trying to go forward but went in reverse. We have video proof but I can't load the video in this document.

Crash

When you put the car in DRIVE it will go in REVERSE. Happened several times and on the last time caused us to back into a pole and mess up the back bumper. We were trying to go forward but went in reverse. We have video proof but I can't load the video in this document.

Crash

While driving the vehicle has stalled/engine shuts off at different speeds and also while the vehicle's steering wheel is turned to move it into a different direction (for example making a right turn at a perpendicular street/road). There is a concern for the operator's safety and others operating around a stalling vehicle especially at higher velocity/speeds and when traffic is heavy. The dealership has recommended an engine replacement, not sure if the dealer has been able to reproduce the problem. Currently, the vehicle has only been inspected by a dealership. The flashing engine light first appeared on 06/07/2024, this would be the second time the vehicle stalled (engine shut off) on the same day.

Passenger side door will not latch or lock. Door remains opened while driving.

2019 Hyundai Veloster. Since November 2022, my vehicle has encountered multiple problems, necessitating extensive periods in repair shops, and I believe these issues have not been addressed satisfactorily. Below is a timeline of the events for your reference: - **December 2022**: Engine replacement was conducted, resulting in the vehicle being in the shop for 7.5 weeks. - **January & February 2023**: The car underwent repairs for damage due to a faulty door and leaking moisture. - **February 2023**: The vehicle was broken into, leading to another round of repairs in April 2023. - **October 2023**: The check engine light activated. Upon taking the vehicle to your dealership, I was informed of a two-month wait for diagnosis and an even further delay for the repair. - **December 2023**: I was advised to leave the car at the dealership for a diagnosis to be conducted several weeks later, with no offer of a courtesy vehicle. - **January 2024**: The dealership diagnosed a low oil code and instructed me to return to the previous service provider to reset it, despite the oil level being adequate. I believe that the engine was not accompanied by proper installation and synchronization of related components, it could indeed lead to a P0017 code. This code indicates a misalignment between the crankshaft and camshaft positions, which can be caused by issues such as a faulty timing chain or belt, incorrect installation of these components, or a problem with the camshaft or crankshaft sensors⁴. The appearance of a P0017 code after an engine replacement can vary in time depending on the specific circumstances of the installation. If the timing components such as the chain or belt, sensors, and related parts are not properly installed or calibrated, the code could show up immediately after the engine is started. In other cases, it might take some time for the code to appear, as the engine's computer tries to adjust the timing and eventually determines it cannot correct.

I had cruise control enabled while driving down the highway. When entering a sweeper turn, the steering wheel locked up completely and could only be moved about 1cm either direction. If this had happened on any mild turn this would have resulted in a crash. The steering wheel locked up entirely at 50mph. I was able to slowly get the car to the side of the road utilizing the 1cm of freeplay in the steering wheel. Steering would not return until I restarted the car. No lights appeared on the dash before, during, or after the incident. Component that failed was 56320-K9000 Power Pack Assembly. Dealer replaced this under warranty after the ECU revealed the component had failed. The component is no longer available for inspection. STEERING GEAR BOX POWER PACK (R-MDPS)|STEERING GEAR BOX POWER PACK (R-MDPS)|STEERING GEAR BOX POWER PACK (R-MDPS)

The contact owns a 2019 Hyundai Veloster. The contact stated while driving at approximately 65 MPH, there was an abnormal sound coming from the engine. The contact stated that it sounded as if the engine was revving without the accelerator pedal being depressed. The contact stated that the RPM revved between 5,000-7,000 RPMs but the vehicle was losing motive power. The contact depressed the accelerator pedal; however, the vehicle was still losing motive power. The contact was able to stop the vehicle. The contact turned off and restarted the vehicle several times however, the vehicle failed to respond while shifting into drive(D). The contact stated the check engine warning light was illuminated. The contact had the vehicle towed to a local dealer. The dealer diagnosed the vehicle and advised the contact that clutch packs 1 and 2 showed DTC codes: P090173 and P090B73. The contact was informed that the clutch packs 1 and 2 along with the clutch actuator and the front brake pads, rotors, and fluid needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was 61,307.

While driving the vehicle the engine stalled in the middle of a turn. We were able to safely move the vehicle to the side of the road immediately out of harms way. The engine would not restart despite adding oil. Prior to the engine stalling there was a light knocking noise but very faint. The check engine or oil lights did not illuminate until after the stall. We had the vehicle towed to our family member's auto shop to research the problem with the engine and he also was not able to get the vehicle to restart. It was confirmed that the piston oil ring had failed and safety recall report 21V-301 was found addressing the same issue with other vehicles same year but not specific to our VIN. We had the vehicle towed to Hyundai dealership to validate the issue and they stated that it was a camshaft dowel and that HyundaiUSA did not feel it fell under the recall notice, we had agreed to a fix to replace the camshaft dowel that was broken upon the initial diagnosis. Upon further review they found that further damage had been done to the engine and now the engine would need to be replaced. HyundaiUSA again said that it didn't fall under the safety recall based on the VIN and would not fully cover the replacement of the engine. Their diagnosis of the damage is identical to what is listed in the Safety recall notice 21V-301. This damage could have caused a much larger issue if the vehicle was being driven on a highway or other high traffic area.

2.0 engine loss of power and stalls. Engine makes knocking noises and timing chain slipping. First reported to dealership on August 21 and was told they could not be able to look at the car for three months. Vehicle was kept out of service for four weeks. Reported to dealership again on 9/14/2023 and visited the dealership on 9/16 after no response. Also notified the dealership of recall involving this year model engine but received no recall notice from Hyundai. All symptoms of this recall were experienced with this vehicle.

My car battery died and I changed the battery. I noticed that the engine lights were on, so I made an appointment to get it checked as well as complete a state inspection. My car fob started acting up and they (Halls Jeep) told me to take it to the Hyundai Service Center because they have the equipment to do so. I took it to the Priority Hyundai and told them of the issue as well as reminded them that there was a recall issue relating to the software in the vehicle. After waiting 4 hours of back and forth, trying to find out what was going on with the car, I saw parked to the side. I asked about it and then another mechanic came and told me that they locked the car and were now unable to unlock it. I told them that there should be some emergency entrance, as all vehicle with a fob has a safety feature to unlock manually. After another while, the service manager decided that the locking issue might be due to the car not being updated (the recall issue) and gave me a loaner car. The service manager also said he did not know how to rectify it and that he would need to contact a different department in Hyundai. I received a call from the manager now saying that it is a mechanical issue and that they are not responsible for anything that happened to my car when they are fixing another issue. I now have a car that I can't lock/unlock and I am not sure what else is wrong due to the software issues. Th software recall does not address all the electrical issues and the dealerships don't know all the issues with the car.

The contact owns a 2019 Hyundai Veloster. The contact stated that while driving at various speeds, the engine would overheat and the vehicle would stall. The vehicle was taken to the local dealer who diagnosed that the engine needed to be replaced. The engine was replaced and failures were remedied. Later while operating the vehicle the contact would become ill and had experienced dizziness and nausea which required medical treatment. The contact was diagnosed with high carbon monoxide levels. The vehicle was later taken to the local mechanic who informed that the carbon monoxide levels inside the cabin of the vehicle were high. The cause f the failure was not determined. The manufacturer was notified of the failure no assistance was offered. The failure mileage was 42,000.

1 injured

My rpm’s were running very low after putting gas to the point the car felt like it would turn off when at idle. I was stopped on a highway at a light when the car revved low and shut off completely. The light was green and I had to sit and try to get it back on, it started right up. Brought it to the dealer and they found no issue with the car. Rpm’s have still been low to the point the car seems like it wants to stall & I’m not sure what to do. It doesn’t make me feel safe driving it.

The contact owns a 2019 Hyundai Veloster. The contact stated that there was an abnormal knocking sound coming from the vehicle. While driving at an undisclosed speed, the vehicle stalled, and the RPMs failed to exceed 200 RPM. The contact stated that the vehicle was consuming an excessive amount of engine oil. The oil warning light was illuminated after the failure. The vehicle was towed to the local dealer to be diagnosed. The contact was notified of rod bearing damage to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The contact stated the failure was related to NHTSA Campaign Number: 21V301000 (Engine). The manufacturer was contacted and informed the contact that the repair offer would be voided if the vehicle was taken to another dealer. The failure mileage was approximately 74,765.

My engine is having the same issue as the other Hyundai Engines that have an active recall for it. The piston oil ring recall. My car is consuming 1qt of oil in roughly 800-1000 miles and burning it into the exhaust. I fear this will continue and cause issues and possibly be a fire hazard like the recall states.

On February 24, 2023, my 2019 Hyundai Veloster Turbo (~36K miles) would not accelerate and began losing power while driving. Problem seemed to be worse while driving uphill. At one point, car would also not go into reverse. Turning car off and then on seemed to resolve the issue with reverse. Similar issue occurred in early November 2022. Local Hyundai service center performed maintenance under warranty on the transmission November 7. Between November 7 and February 24, there were no observable issues with the vehicle while driving.

Defective engine connecting-rod bearings in the engine that wore out and caused the engine engine to seize and fail while driving on the highway. Flashing check-engine light came on and reduction in power.

Defective connecting rod bearings that wore out early, which can lead to engine failure and stalling which almost led to a car crash. The connecting-rod bearings in the engine that could wore out prematurely and damage the engine resulting in engine failure. This created abnormal knocking noises from the engine , reduced power and flashing check engine light.

I was driving to work on the morning of July 14, 2022. I was in a work zone with cones on both sides of me my vehicle lost compression as I was compressing the accelerator I started hearing a low rapping or knocking sound, This knocking increased and repetition rather quickly and my car would not accelerate as it had been. I exited the This knocking increased and repetition rather quickly and my car would not accelerate as it had been. I exited the Work zone area, near where my work is and as soon as I turned off my brake pedal would barely compress I literally had to put all of my body white on the brake pedal to get my vehicle to slow down I had smoke coming out of my engine compartment and lost all auxiliary power to the vehicle. I was able to Let the smoke out and see if the engine was actually on fire. It was not. I had no idea what was going on or why my pretty new vehicle Was doing this. I had it towed to a body shop who did a full diagnostic of the engine, and they came out with a report saying there was internal mechanical problems and that all of the engine oil had dissipated at a rapid rate.

The contact's daughter owns a 2019 Hyundai Veloster. The contact stated that while her daughter was driving at an undisclosed speed, the check engine warning light illuminated and the engine seized. The vehicle was towed to the dealer where it was diagnosed that a faulty oil filter caused the engine to fail. The dealer informed the contact that the engine needed to be replaced. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure but declined the engine replacement. The manufacturer informed the contact that the warranty was void due to after-market parts on the vehicle. The contact related the failure to NHTSA Campaign Number: 21V301000 (Engine) however, the VIN was not included in the recall. The failure mileage was approximately 44,000.

DRIVER'S SIDE DOOR HANDLE DOES NOT WORK ON THE OUTSIDE IN COLD WEATHER, THE CAR HAS TO BE ENTERED FROM THE PASSENGER SIDE DOOR AND OPENED FROM THE INSIDE.

This has happened 3 times. While driving the car it slows down and RPMS go up. I’ll be driving on expressway at approximate 60 mph then slows down to a crawl on expressway. 1st time it happened the dealer said a hose came off the turbo causing the issue. 2nd time it happened they said it was a coil. Now it happened again I almost got into and accident as the engine revs but transmission not engaging

VEHICLES HVAC BLOWER MOTOR MAKES A HIGH PITCHED SQUEAL/WHINE WHEN BEING USED ON LOWER FAN SETTINGS. THE BEARINGS IN THE MOTOR SEEM TO NOT BE PROPERLY OILED AND CREATES A SOMETIMES LOUD SOUND WHEN BEING USED DO TO THE SCRAPING IN THE MOTOR HEAD. THIS IS WORSENED WHEN ON ROUGH TERRAIN, THE SQUEALING/WHINING WILL BECOME WORSE AND MORE PERSISTENT.

DURING STARTUP. WHEN CAR IS FIRST IGNITION, WHILE IN NEUTRAL PROCEED TO 1ST GEAR AN AUDIBLE SOUND WILL BE HEARD FROM RIGHT COLUMN AND DISAPPEARS. IT WILL HAPPEN EVERY START UP SEQUENCE. I SENT MY CAR FOR SERVICE AND THEY TOLD ME THAT IT COULD BE THE ELECTRONIC DIFFERENTIAL LOCK.

THE VEHICLES DRIVER'S SIDE DOOR HANDLE DOES NOT WORK ON THE OUTSIDE IN COLD WEATHER, THE CAR HAS TO BE ENTERED FROM THE PASSENGER SIDE DOOR AND OPENED FROM THE INSIDE. CAR IS PARKED AND UNLOCKED BUT OUTER DOOR HANDLE, ON THE DRIVERS DOOR, REFUSES TO OPERATE CORRECTLY.

DRIVERS SIDE DOOR WILL NOT OPEN FROM THE OUTSIDE IN COLD (FREEZING OR BELOW) TEMPERATURES. IT SEEMS TO STILL BE LOCKED, DESPITE UNLOCKING THE CAR AND BEING ABLE TO OPEN ALL OTHER DOORS ON THE CAR. MUST BE OPENED FROM THE INSIDE THROUGH THE PASSENGER DOOR.