2012 BMW 328I

The inner film on the central display console that shows navigation, multimedia and other information detached and made the display unreadable.

INCIDENT SUMMARY: On January 9, 2026, at approximately 1:30 PM, while traveling at 50 MPH in North Carolina, the vehicle experienced a sudden, catastrophic engine seizure without any prior "Limp Mode" warning or Check Engine Light. This resulted in an immediate, total loss of motive power in active traffic. I was forced to navigate a dead multi-ton vehicle across lanes without power steering or vacuum-assisted braking, narrowly avoiding a high-speed collision. TIMELINE & NEGLIGENCE: This vehicle was purchased from an independent retail dealer on December 20, 2025—less than 21 days prior to this life-threatening failure. The vehicle was sold with an "Open" status for Safety Recall 23V-707. The failure occurred exactly as described in the recall’s warning: a catastrophic stall at speed. TECHNICAL EVIDENCE: A non-invasive borescope inspection of the cylinders has confirmed the presence of metallic "silver chunks" (sheared bolt heads) and "half-moon" impact marks on the piston crowns, indicating a total timing failure and internal mechanical collision (piston-to-valve contact). REQUIRED REMEDY: This incident is a direct manifestation of the safety risk documented in Recall 23V-707. Per BMW Service Bulletin SIB 11 09 23, the presence of sheared bolt heads and seized internals constitutes "Catastrophic Consequential Damage." I am filing this report to ensure federal oversight of BMW North America’s obligation to provide a complete engine replacement, as the safety defect was present at the time of sale and resulted in a near-fatal incident within 300 miles of ownership.

INCIDENT SUMMARY: On January 9, 2026, at approximately 1:30 PM, while traveling at 50 MPH in North Carolina, the vehicle experienced a sudden, catastrophic engine seizure without any prior "Limp Mode" warning or Check Engine Light. This resulted in an immediate, total loss of motive power in active traffic. I was forced to navigate a dead multi-ton vehicle across lanes without power steering or vacuum-assisted braking, narrowly avoiding a high-speed collision. TIMELINE & NEGLIGENCE: This vehicle was purchased from an independent retail dealer on December 20, 2025—less than 21 days prior to this life-threatening failure. The vehicle was sold with an "Open" status for Safety Recall 23V-707. The failure occurred exactly as described in the recall’s warning: a catastrophic stall at speed. TECHNICAL EVIDENCE: A non-invasive borescope inspection of the cylinders has confirmed the presence of metallic "silver chunks" (sheared bolt heads) and "half-moon" impact marks on the piston crowns, indicating a total timing failure and internal mechanical collision (piston-to-valve contact). REQUIRED REMEDY: This incident is a direct manifestation of the safety risk documented in Recall 23V-707. Per BMW Service Bulletin SIB 11 09 23, the presence of sheared bolt heads and seized internals constitutes "Catastrophic Consequential Damage." I am filing this report to ensure federal oversight of BMW North America’s obligation to provide a complete engine replacement, as the safety defect was present at the time of sale and resulted in a near-fatal incident within 300 miles of ownership.

INCIDENT SUMMARY: On January 9, 2026, at approximately 1:30 PM, while traveling at 50 MPH in North Carolina, the vehicle experienced a sudden, catastrophic engine seizure without any prior "Limp Mode" warning or Check Engine Light. This resulted in an immediate, total loss of motive power in active traffic. I was forced to navigate a dead multi-ton vehicle across lanes without power steering or vacuum-assisted braking, narrowly avoiding a high-speed collision. TIMELINE & NEGLIGENCE: This vehicle was purchased from an independent retail dealer on December 20, 2025—less than 21 days prior to this life-threatening failure. The vehicle was sold with an "Open" status for Safety Recall 23V-707. The failure occurred exactly as described in the recall’s warning: a catastrophic stall at speed. TECHNICAL EVIDENCE: A non-invasive borescope inspection of the cylinders has confirmed the presence of metallic "silver chunks" (sheared bolt heads) and "half-moon" impact marks on the piston crowns, indicating a total timing failure and internal mechanical collision (piston-to-valve contact). REQUIRED REMEDY: This incident is a direct manifestation of the safety risk documented in Recall 23V-707. Per BMW Service Bulletin SIB 11 09 23, the presence of sheared bolt heads and seized internals constitutes "Catastrophic Consequential Damage." I am filing this report to ensure federal oversight of BMW North America’s obligation to provide a complete engine replacement, as the safety defect was present at the time of sale and resulted in a near-fatal incident within 300 miles of ownership.

While traveling at night on the toll road between Washington, DC and Pittsburgh, PA, the vehicle suddenly shut off without warning. Power was lost completely, including power steering, while in motion on a major freeway, creating an immediate and severe risk of collision for us and surrounding motorists. Although the vehicle did restart, it stalled again shortly afterward while still on the toll road. The failure repeated when decelerating on the highway or coming to a stop after exiting. At no point were there warning lamps, check-engine lights, messages, or reduced-power mode indicators prior to the stalls; the shutdowns occurred without any advance notice. The vehicle was towed to an independent BMW-only repair shop in Pittsburgh. Their initial assessment indicated a high likelihood that the failure involved the VANOS assembly bolts, though the engine was not disassembled at that time, so the diagnosis could not be confirmed with certainty. Because the shop did not have immediate availability, we were asked to transport the car home until they could perform a full repair. After sitting for several weeks, the car was towed back for further inspection, at which point the shop discovered that a VANOS bolt had likely sheared off and caused irreparable damage to the engine. Our only options now are to replace the engine or scrap the vehicle. The vehicle remains in Pittsburgh, PA in our possession and is available for inspection upon request. At this time, the failure has not been reproduced or confirmed by a BMW dealer, nor has it been inspected by the manufacturer, police, or insurance representatives. Importantly, there is an existing recall on VANOS bolts for the 328xi station wagon, but our vehicle’s production date ([XXX]) falls just outside the recall window of October 1, 2009–August 4, 2011. Notably, for the sedan body model, the recall window was extended until December 6, 2011. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Dealer refused to cover DME that failed immediately after recall 24V-608 work. In early June 2025, I contacted my local BMW dealership about an overheat notification I received while driving. They confirmed there was an open recall on the vehicle for a water pump connector (Recall 24V-608). I had the vehicle towed to their location. They sent me a video walkaround that characterized everything looked good, except the water pump connector which had failed. Several days later, I was informed the recall repair had been completed but when they plugged in the new water pump connector, the DME shorted and they had to unhook the battery. Despite my best attempts to get this consequential damage covered as part of the recall work, BMW refused. I was told I had to come pick up the car as-is or pay for repairs. When I looked into the issue further online, I learned that if I had chosen to pick up the car, hook up the battery and attempt to start and drive it, I could have found myself stuck inside the car (electronic locks) with a DME that literally caused the whole car to start on fire. Thank goodness I didn't go that route. After further investigation into the recall issue (24v-608), I have learned the entire basis of the recall was risk of a "thermal event" caused as a result the faulty water pump connector shorting out. BMW never denied this when I brought it up. It is infuriating that BMW is suggesting the DME shorting out is not related to or covered by the water pump recall issue. A risk of thermal event is stated in the recall notice, and the DME literally shorted out DURING the recall repair work. They quoted me something like $5,000-7,000 to have the car drivable again. I'm at a complete loss.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, the temperature gauge indicated that the engine was overheating, and shortly afterwards the vehicle lost motive power in the middle of the roadway. The contact stated that several unknown warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the fuse box. The contact was informed that the fuse box had melted and was stuck to the battery. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 161,000.

My BMW IS OVERHEATING ITS BEEN IMAT BMW OF DOWNTOWN FOR 8 days and they’re trying to charge me to repair my melted fuse box,cooling systems and battery, damage that has occurred as a default of the pcv

DRIVE TRAIN MALFUNCTION. On June 25th 2025, for the second time I got this Drive Train Malfunction Issue on my 328i 2012 Model. The car just stopped in middle of road ( thank GOD not on a freeway ; otherwise, this would have resulted in multi car accidents and could have costed people's life including mine ). The car just died and STOPPED all of a sudden in middle of road and when I tried to start it, it only crank's . After waiting for about 10 minutes, it started . I had exactly same issue earlier in July 2024 and that time BMW service found high pressure fuel pump to be defective and they changed that. I was told by my BMW dealer that certain model and year BMW has this issue and it is well know. But I do see BMW issuing to its customers or doing anything. If the car just stops without any warning to pull over etc. while you are driving is very serious is VERY SERIOUS and LIFE- THREATENING ISSUE . Imagine one is driving at 70 miles an hour on a busy freeway and car abruptly stops ( like my car did , twice in last 11 months, thank god not on freeway though) and there are several cars behind you driving at more or less at same speed; this will result in multi cars collision and multiple accidents and deaths. I request NHTSA to take this serious issue on priority basis and do something ASAP.

The contact owns a 2012 BMW 328I. The contact stated that while starting the vehicle, the engine overheated, with a message that the engine was overheating displayed. The contact stated that while driving at an undisclosed speed, the vehicle stalled with the same message displayed. The vehicle was able to restart. The vehicle was towed to an independent mechanic, where the vehicle was not diagnosed or repaired. The vehicle was taken to the dealer, where it was not diagnosed or repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 172,000.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, the temperature gauge started to indicate that the engine was overheating, prompting the contact to discontinue driving the vehicle. The check engine warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The VIN was included, but the vehicle had not been repaired. The manufacturer was not notified of the failure. The failure mileage was 140,000.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, the temperature gauge started to indicate that the engine was overheating, prompting the contact to discontinue driving the vehicle. The check engine warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The VIN was included, but the vehicle had not been repaired. The manufacturer was not notified of the failure. The failure mileage was 140,000.

The contact owns a 2012 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part needed for the recall repair was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part needed for the recall repair was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that upon taking the vehicle to an independent mechanic for a diagnostic test, the mechanic discovered a defect with the VANOS bolts. The vehicle was then taken to another independent mechanic for a second opinion, and the contact was provided with the same information as the first mechanic. The contact was provided with information on NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); which the mechanic linked to the failure. The contact called two dealers and was informed that there were no recalls on the VIN. The contact was then referred to the manufacturer, who later referred the contact to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 90,000.

The contact owns a 2012 BMW 328I. The contact stated while driving at approximately 65 MPH, the vehicle stalled. There was no warning light illuminated. The vehicle was taken to an independent mechanic to be diagnosed. The vehicle was not yet diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 99,263.

The contact owns a 2012 BMW 328I. The contact stated that while driving at various speeds, the vehicle failed to accelerate as intended while the accelerator pedal was depressed. In addition, the contact stated that there was white smoke coming from under the hood and from the exhaust tips. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the coolant pump connector had failed and needed to be replaced. An appointment with the dealer was scheduled to inspect the vehicle. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 106,000.

The contact owns a 2012 BMW 328I. The contact stated that while driving 65 MPH, a message to pull over immediately was displayed, and the vehicle stalled. The contact was able to pull to the side of the road. The vehicle failed to restart and was towed to the dealer, where it was diagnosed that the timing chain had failed and needed to be replaced. The vehicle was not repaired. Additionally, the contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 114,000. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that while driving 65 MPH, a message to pull over immediately was displayed, and the vehicle stalled. The contact was able to pull to the side of the road. The vehicle failed to restart and was towed to the dealer, where it was diagnosed that the timing chain had failed and needed to be replaced. The vehicle was not repaired. Additionally, the contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 114,000. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact received notification of 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

It’s sounds like it’s moving but it doesn’t.

The contact owns a vehicle 2012 BMW 328i. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a vehicle 2012 BMW 328i. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328i. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328i. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, there was white smoke coming from the exhaust. There was no warning light illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the water pump plug connector. The vehicle was not repaired. The vehicle was then taken to the dealer, who confirmed the diagnosis. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); the VIN was included, but parts were not yet available. The manufacturer was notified of the failure but provided no assistance. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was 125,000.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, there was white smoke coming from the exhaust. There was no warning light illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the water pump plug connector. The vehicle was not repaired. The vehicle was then taken to the dealer, who confirmed the diagnosis. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); the VIN was included, but parts were not yet available. The manufacturer was notified of the failure but provided no assistance. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was 125,000.

The contact owns a 2012 BMW 328i. The contact stated that upon starting the vehicle, there was smoke coming out from the exhaust pipe, and there was a burning smell coming from the engine compartment. The check engine warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed that the oil pan was leaking near the water pump. The dealer replaced the thermostat gasket, the valve cover gasket, the cylinder head cover, the ISA screws and washer, the high-pressure pipe, and the gasket flange. Additionally, the dealer performed an oil change and added coolant to the vehicle. The vehicle was repaired. The contact later received notification of NHTSA Campaign Number: 24V608000(Electrical System, Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and confirmed that the parts were not yet available. The failure mileage was approximately 115,783. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328i. The contact stated that upon starting the vehicle, there was smoke coming out from the exhaust pipe, and there was a burning smell coming from the engine compartment. The check engine warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed that the oil pan was leaking near the water pump. The dealer replaced the thermostat gasket, the valve cover gasket, the cylinder head cover, the ISA screws and washer, the high-pressure pipe, and the gasket flange. Additionally, the dealer performed an oil change and added coolant to the vehicle. The vehicle was repaired. The contact later received notification of NHTSA Campaign Number: 24V608000(Electrical System, Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and confirmed that the parts were not yet available. The failure mileage was approximately 115,783. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that while driving at approximately 5 MPH, there was smoke coming from the engine compartment. The check engine warning light and several other unknown warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was unknown. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that while driving at approximately 5 MPH, there was smoke coming from the engine compartment. The check engine warning light and several other unknown warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was unknown. VIN tool confirms parts not available.

The contact owns a 2012 BMW 328I. The contact stated that while driving at an undisclosed speed, the vehicle stalled with the check engine warning light illuminated. The vehicle was restarted; however, the failure recurred. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the VANOS assembly bolts had failed and needed to be replaced. The vehicle was not repaired. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 122,000.

Without warning and no OBD2 codes thrown, my car and many others in the E90 (2007-2012) 3-series (N52 engine) will stall, lose power, and/or burn excessive oil when the integral PCV - valve cover starts to clog. Many owners on the BMW boards online have reported similar problems. The E90 3-series BMWs have an integral, internal positive crankcase ventilation system as part of the engine's plastic valvetrain (engine cover or valve cover) cover. Inside the valve cover is a series of cyclones that separate the oil from the valvetrain gasses and route the gasses to the PCV system. Repair is > $4000

Without warning and no OBD2 codes thrown, my car and many others in the E90 (2007-2012) 3-series (N52 engine) will stall, lose power, and/or burn excessive oil when the integral PCV - valve cover starts to clog. Many owners on the BMW boards online have reported similar problems. The E90 3-series BMWs have an integral, internal positive crankcase ventilation system as part of the engine's plastic valvetrain (engine cover or valve cover) cover. Inside the valve cover is a series of cyclones that separate the oil from the valvetrain gasses and route the gasses to the PCV system. Repair is > $4000

My car lost power. It would come and go. Now it's gone. The codes that come up pertain to the wheel speed sensor and timing.

My car lost power. It would come and go. Now it's gone. The codes that come up pertain to the wheel speed sensor and timing.

My car lost power. It would come and go. Now it's gone. The codes that come up pertain to the wheel speed sensor and timing.

The contact owns a 2012 BMW 328I. The contact stated while driving at an undisclosed speed, the vehicle shuddered and stalled. The contact stated that the vehicle vibrated, and the brakes were independently activated. Additionally, the contact stated that the “Service Required” warning light was illuminated. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact stated that recently the transfer case was replaced by an independent mechanic. The manufacturer was made aware of the failure. The failure mileage was 110,000.

I had just came off the interstate off ramp I-44 and Chestnut Expressway when out of nowhere my Drivetrain Malfunction warning came on then the car started shaking horribly and sounded awful. Pulled over immediately and it wouldnt restart and if it did it would shut itself off almost immediately. It is currently at BMW of Springfield, they said all my sensors are correct but believe that the timing chain guide teeth busted somehow in the engine?!? Thought it could be due to the VANOS recall but my VIN isn’t included and clearly should be.

I purchased this vehicle [XXX]. Within 2 days a rattle could be heard coming from bmw vanos area, VANOS is a variable valve timing system used by BMW on various automotive petrol engines since 1992. I ceased all use of this vehicle on [XXX], only 3 days. Through my own research i found recall 23v-707 which lists my vehicle and this problem. I had the car towed to a bmw repair shop Harrison Motorsport. The owner said the engine needs to be replaced. Next I tried in Vane to get bmwna or bmwag to warrant this repair. I have numerous emails from bmwag of munich germany saying they are aware and their north america partners will be in touch. The recall states you may drive this vehicle even though it may produce a crash,,,,huh? I have another bmw specialist 4 miles from my home. I drove the car this time to Brian Motor Works. The owner here stated that without a doubt these bolts had come loose. We planned to have him fix it the next week. Still at this time there were no dashboard warnings or internal codes to be found. I tried to drive as slow as possible back home. I went 2 miles and the 1st lights appeared on the dashboard. The engine shut down and I narrowly avoided a crash. The engine will no longer turn over and I believe it has seized. Through research this issue was 1st admitted in 2014. bmw stated it illegal to sell this vehicle as a certified pre owned bmw until these bolts are checked and or replaced. Mine have never been checked or replaced. I am thankful each day that my family was not with me when this happened, My attention was totally on this vehicle when it lost all power to steer or brake. I was very lucky this day, but I fear others will not be so fortunate. thank you. [XXX] [XXX] 770-329-6384 vin wbadw3c58ce[XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2012 BMW 328I. The contact stated that while driving at approximately 40 MPH, the vehicle stalled. No warning lights were illuminated. The vehicle was not able to be restarted. The contact stated that after various attempts, the vehicle was shifted in neutral to be towed. The vehicle was towed to an independent mechanic where it was diagnosed and determined that the engine needed to be replaced. The local dealer was made aware of the failure; however, the dealer confirmed that the vehicle was out of warranty. The vehicle was not repaired. The manufacturer was made aware of the failure; however, no assistance was provided. The failure mileage was approximately 133,000.

The contact owns a 2012 BMW 328I. The contact stated while driving 30 MPH, there was an abnormal sound coming from the engine. There was no warning light illuminated. The contact stated that the failure had been recurring. The vehicle was taken to an BMW certified mechanic, where it was diagnosed, and the mechanic determined that the engine needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling). The dealer and the manufacturer were notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was approximately 138,000.

Yesterday morning 3/24/24 , car stalled on highway with Fuel Pump message on dashboard. Car would not start and had to be towed.

As I was going down the highway may car lost power. I had to pull onto the shoulder and turned the car off. I then tried to start it but is would not start back up. I left it on the side of the highway for a few hours. Went back and it started back up but it was in limp mode, so I drove it to a shop. This car gave me no problems until this point. The shop I took it to couldn't help me. So I took it to Century BMW in Greenville SC. They told me I needed a motor that was going to cost me $14,000 to fix. I asked them to put my motor back together ( the top part of the motor). They informed me it would cost me $600 to do so. I got my car back with the motor not put back like they got it. It has been sitting every since.

Passenger restraint system malfunction. My vehicle as well as thousands of others have the chronic and unsafe issue of the passenger occupancy sensor malfunctioning. In order to remove warning on dash it’s either a $2,000 repair, or a $40 bypass which basically places the seat as constantly occupied, sticking the passenger airbag in the ‘on’ position. Vehicle is available for inspection. With this malfunction, any person that sits in the passenger front seat is at risk of injury or death in the event of a collision. Malfunction has been confirmed by both a dealer and an independent service center. Vehicle was inspected by the dealer, but no police or insurance company. Vehicle was purchased with the malfunction and the warning lights have been on for several years. With the massive number of vehicles of this make with a range of different mileage, with this issue, a recall is not only needed but warranted and should be mandated with this being a major safety issue.

Passenger restraint system malfunction. My vehicle as well as thousands of others have the chronic and unsafe issue of the passenger occupancy sensor malfunctioning. In order to remove warning on dash it’s either a $2,000 repair, or a $40 bypass which basically places the seat as constantly occupied, sticking the passenger airbag in the ‘on’ position. Vehicle is available for inspection. With this malfunction, any person that sits in the passenger front seat is at risk of injury or death in the event of a collision. Malfunction has been confirmed by both a dealer and an independent service center. Vehicle was inspected by the dealer, but no police or insurance company. Vehicle was purchased with the malfunction and the warning lights have been on for several years. With the massive number of vehicles of this make with a range of different mileage, with this issue, a recall is not only needed but warranted and should be mandated with this being a major safety issue.

Passenger restraint system malfunction. My vehicle as well as thousands of others have the chronic and unsafe issue of the passenger occupancy sensor malfunctioning. In order to remove warning on dash it’s either a $2,000 repair, or a $40 bypass which basically places the seat as constantly occupied, sticking the passenger airbag in the ‘on’ position. Vehicle is available for inspection. With this malfunction, any person that sits in the passenger front seat is at risk of injury or death in the event of a collision. Malfunction has been confirmed by both a dealer and an independent service center. Vehicle was inspected by the dealer, but no police or insurance company. Vehicle was purchased with the malfunction and the warning lights have been on for several years. With the massive number of vehicles of this make with a range of different mileage, with this issue, a recall is not only needed but warranted and should be mandated with this being a major safety issue.

The contact owns a 2012 BMW 328I. The contact stated that the temperature sensor on the instrument panel had initially failed to operate as needed; over time, the entire instrument panel had gone blank while the vehicle was being driven. In addition, the battery would continue to run while the vehicle was turned off; as a result, the vehicle would shut off while driving at various speeds. The vehicle was taken to various independent mechanics and each stated that the instrument cluster was defective. Despite multiple battery and temperature gauge replacements, the failure persisted. The manufacturer was notified of the failure and informed him that there were no recalls on the vehicle and referred the contact to the NHTSA Hotline for assistance. The vehicle was not repaired. The failure mileage was approximately 84,000.

The contact owns a 2012 BMW 328I. The contact stated during cold starts, there was a large puff of bluish-white smoke coming from the tail pipe. The contact stated no warning light was illuminated. The contact had taken the vehicle to an independent mechanic, where it was diagnosed and determined that the oil supply line needed to be replaced. The vehicle had not been repaired. The contact stated that the failure had become a recurring failure. The independent mechanic researched online and related the failure to manufacturer Voluntary Emissions Recall Campaign Number: 16E-A05 Engine; Replace Turbocharger Oil Supply Line (Engine and Engine Cooling). The manufacturer had been informed of the failure. The failure mileage was approximately 65,000.

The contact owns a 2012 BMW 328I.The contact stated while driving 70 MPH, the vehicle independently accelerated at high speed before the vehicle shut off with the message “Transmission Not in Park” displayed. The contact was able to pull over on the side of the road, and after the vehicle cooled down the contact was able to restart the vehicle and the vehicle operated normally. The vehicle was taken to the dealer and the fuel pump was replaced but the failure reoccurred. The vehicle was taken to an independent mechanic, but no cause for the failure was found. The vehicle was taken to the dealer and no failure was found. The vehicle was not repaired. The manufacturer was contacted and stated that the VIN was not under recall for the failure. The failure mileage was 117,000.