2011 BMW 328I Recalls, Complaints & Safety

The contact owns a 2011 BMW 328I. The contact stated that upon starting the vehicle, the low oil pressure warning light illuminated, and the vehicle stalled. The vehicle was towed to an independent mechanic, where it was diagnosed, and determined that the VANOS bolts had failed and needed to be replaced. The vehicle was not repaired due to the cost. The contact related the failure to TSB Number: SIB 11 04 14. The manufacturer was notified of the failure and informed the contact that the vehicle was covered under the TSB. The failure mileage was approximately 157,637.

The contact owns a 2011 BMW 328I. The contact stated that on several occasions while driving on the streets and the highway, the vehicle lost automotive power. There were no warning lights illuminated at the time of the failure. The contact stated that the vehicle jerked unexpectedly, stalled, and failed to accelerate over 30 MPH. The vehicle was towed to an independent mechanic but was not diagnosed or repaired. The mechanic referred the contact to the dealer for further assistance and stated that the failure could be related to a recall. The vehicle was towed to the dealer, but was not diagnosed or repaired. The contact stated that the failure started after the vehicle was repaired under an air bag recall by the dealer, and the failure persisted. The manufacturer was made aware of the failure. The approximate failure mileage was 200,000.

The contact owns a 2011 BMW 328I. The contact stated that while driving at various speeds, there was a burning odor coming from the vehicle. The odor was more prominent while the vehicle was idling. The RPM fluctuated while idling, causing the vehicle to stall. The contact would depress the brake pedal, place the vehicle in neutral, turn off, and restart the vehicle to accelerate and continue driving. The air bag warning light was illuminated, and the message, "Check Engine Soon," was displayed. The vehicle was taken to a certified mechanic, and a diagnostic code was retrieved for Positive Crankcase Ventilation (PCV) failure; however, no repairs were completed. The contact completed some research and learned that the failure could be occurring due to air entering the brake lines. The contact also found information about NHTSA Campaign Number: 22V119000 (Engine); however, the VIN was not included. The vehicle was not taken to the dealer, diagnosed, or repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 133,000.

Fuel Pump Control Module and Fuel Pump Failed at highway speeds. There was a notification warning for a failed fuel pump and then the engine shut down and stalled at highway speeds within seconds.

> While driving the car, low oil pressure indicator came on and within less than a mile later there was a sudden loss of power, engine stalled and then would not start again, requiring vehicle to be towed off the road and to a repair garage. Yes, vehicle is available for inspection upon request. >Vehicle was immobile on the road putting driver of vehicle and other vehicles on the road at risk of accident and injury. > Attached documentation reviews the issue. > Vehicle originally inspected by non-dealership garage that strongly recommended the vehicle be evaluated by BMW. Vehicle was towed to and inspected by BMW Sewickley [XXX] . BMW states not covered under Vanos recall. >Only immediately prior to stall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

> While driving the car, the low oil pressure indicator came on, and within less than a mile later there was a sudden loss of power, engine stalled and then would not start again, requiring the vehicle to be towed off the road and to a repair garage. > Vehicle was immobile on the road putting driver of this vehicle and other vehicles on the road at risk of an accident and injury. > Vehicle originally inspected by non-dealership garage that strongly recommended the vehicle be evaluated by BMW. Vehicle was towed to and has been inspected by BMW Sewickley [XXX] . > Only immediately prior to stall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Engine lost all oil pressure, smoke came through vents with the smell of burnt oil. Engine stalled, intake camshaft no longer moves when the engine is trying to turn over. Vanos system failed.

The power cable to my battery needed to be replaced from the front to the rear. This seems like the recall NHTSA CAMPAIGN ID: 13V044000 but my car was not listed for it.

The contact owns a 2011 BMW 328I. The contact stated that while driving approximately 65 MPH, the check engine warning light illuminated, and the vehicle hesitated and stalled. The vehicle was restarted several times but continually stalled. The vehicle was later towed to the residence. The contact examined the engine and discovered metal shavings in the VANOS solenoid engine oil. The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure. The vehicle was not yet repaired. The failure mileage was 120,000.

The contact owns a 2011 BMW 328I. The contact stated that while driving at an undisclosed speed, the contact noticed an abnormal dinging sound coming from underneath the hood. The vehicle was taken to the dealer where it was diagnosed with a detached VANOS bolt. The contact was informed that the failure was due to unrepaired recall NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling). The recall repair was performed. The vehicle was repaired. The contact stated that when the vehicle was released to the contact, the contact stated that the vehicle was shaking violently, and the RPM was fluctuating. In addition, the engine shut off while idling. The contact stated that the failure occurred before leaving the dealer. The dealer requested that the vehicle remain at the dealer for inspection. The vehicle was taken back to the dealer the following day. The vehicle was inspected, and the contact was informed that the failure was not related to the recall. The contact was requested to provide a diagnostic fee for further diagnostic tests and the contact declined. The contact stated that the vehicle was in worse condition after the recall repair was performed. The manufacturer was not made aware of the failure. The failure mileage was 91,000.

Footwell module (FRM) module went out after negative battery disconnect to change fuse. Module being inoperable is causing windows to not operate,interior lighting not working, headlights stay dim (not good for nightime driving), blinkers inoperable (not good for driving with windows not working- no arm signals), dash light also inoperable.

Door handle plastics are disintegrating in to a soft sticky matter. Please advice as this seem to a poor decision on the type of material need in the door handles.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 23V707000 (ENGINE AND ENGINE COOLING). The recall repair was completed; however, on the drive home after the vehicle was retrieved, while driving 60 MPH, the engine seized. The contact stated that the vehicle was sluggish and hesitated before stalling in the middle lane of the highway. The oil pressure warning light was illuminated. The contact attempted to restart the vehicle, and after several attempts, the vehicle failed to restart. The contact was able to coast to the side of the road. The vehicle was towed to the dealer, where it was determined that the incorrect oil filter was installed on the vehicle. The vehicle was repaired. The contact towed the vehicle back to the residence. The manufacturer was made aware of the failure and offered the contact a 10% discount on a new engine. The failure mileage was 126,657.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 22V119000 (ENGINE AND ENGINE COOLING). The contact had received various unknown notifications of NHTSA recalls. The vehicle was taken to the dealer, where the vehicle was repaired. The contact stopped by the dealer to pick up the vehicle, and when the vehicle was started, there was an abnormal sound coming from the engine. The contact stated that the vehicle was idling abnormally. The contact left the vehicle at the dealer. The contact believed that the dealer had damaged the vehicle. The dealer informed the contact that the vehicle had other issues that the contact needed to repair for the dealer to repair the vehicle again. The manufacturer was not notified of the failure. The failure mileage was 134,184.

The contact owns a 2011 BMW 328I. The contact stated while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to pull to the shoulder of the roadway, where the vehicle failed to restart. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was unknown.

The contact owns a 2011 BMW 328I. The contact stated that while attempting to start the vehicle, the electrical system failed to function as intended. The contact stated there was no warning light illuminated. The vehicle eventually started; however, the failure occurred. The vehicle was not diagnosed or repaired. The contact stated that the failure persisted. The manufacturer had been informed of the failure and transferred the contact to the NHTSA Hotline. The contact researched online and related the failure to NHTSA Campaign Number: 13V044000 (Electrical System); however, the VIN was not included. The failure mileage was approximately 116,000.

The contact owns a 2011 BMW 328I. The contact stated that while driving at various speeds and attempting to slow down, the vehicle started to jerk abnormally, with the check engine warning light illuminated. The vehicle was taken to a local dealer and was diagnosed, and the contact was informed that the camshaft adjusting unit was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 106,000.

RE: Recall on 2011 328i Vin# [XXX] I drove the car to run an errand, car was running ok but had a miss. During my drive home, the car stalled. I had to quickly coast to a parking lot in order not to get hit by the car behind me. I tried to restart the car, but it acted as if it needed a jump. Tried to jump the car but it turned over slowly without starting. Ended up getting it towed to Metairie very early the next morning, due to parades. Had a friend of mine, a BMW shop owner, take a look at the car. He told me that he found out that it had a few recalls and he thought that may be the problem. I spoke with a service advisor at BMW dealer that checked the vin and said the recalls would be taken care of along with anything it caused. I made the appointment and had it towed to BMW dea;er. I was assigned to Erin C, Service Advisor, when I made my appointment. My appointment was for 7:30 AM on the 28th of March. I heard from Erin at 4:30 that afternoon with an update. She told me that I had a seized engine and it was going to cost ten thousand or more to replace the engine. I asked if the recall was done on it, because the recall stated that one of the indicators of the Vanos issue was that it would not start any more. I also found information saying that stalling, engine seizing, and oil starvation can be dangerously caused by the recall. Erin stated that they would take the valve cover off to confirm. Didn’t hear from her on Friday, or over the weekend. I got her on the phone Monday evening at 5:30 PM. Erin told me the same information that after they took off the valve cover and videoed it (have not seen that video yet). That my engine was seized. She assured me that they hooked up the car to communicate with the engineers who confirmed, from all the evidence, that the engine seizing was not caused by the recall but lack of oil circulation. If she had a diagnostic done on the car, she had not shared any codes found with me at this INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATIO

The contact owns a 2011 BMW 328i. The contact had received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); and the vehicle was taken to the dealer for the recall repair. The contact stated that upon returning to pick up the vehicle, he was informed that the vehicle would no longer start, requiring the vehicle to be towed back to the residence. The dealer diagnosed a failure with the VANOS solenoid. The vehicle was not repaired. After investigating the failure, the contact related the failure to the recall repair, and the dealer seemed to concur with the sentiments but had not provided any further assistance. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 240,000.

i took my car in for the vanos bolts recall at a bmw dealership they said they could fix the car.keep in mind i drove the car there just fine and now there saying its gonna cost $3300 to fix my car and its not drivable and idk what to do because im not spending that much money when i took my car in for a recall

Dear Sir/Madam, I am writing to formally file a complaint against Burdick BMW, located in Syracuse, NY, regarding their failure to address my request for a recall-related repair on my vehicle. Despite multiple attempts to schedule an appointment, I have received no response or follow-up from the dealership. Over the past month, I have contacted Burdick BMW a total of four (4) times via phone regarding a recall service for my vehicle. The contact was made on [XXX]. Each time, I spoke with a customer representative who assured me that a supervisor would return my call to schedule an appointment. However, I have never received a call back nor been provided with any opportunity to have my vehicle serviced. This ongoing lack of communication and failure to act on a manufacturer-issued recall raises serious concerns about the dealership's commitment to customer service and safety compliance. As a consumer, I am entitled to have my vehicle serviced in accordance with recall requirements, and Burdick BMW’s inaction has not only caused inconvenience but may also pose a safety risk due to the unresolved recall issue. Given that my attempts to resolve this matter directly with the dealership have been unsuccessful, I request that appropriate action be taken to ensure Burdick BMW fulfills its obligations. I kindly ask that you investigate this matter and take the necessary steps to hold Burdick BMW accountable for their failure to schedule or complete recall-related repairs in a timely manner. Additionally, I request assistance in obtaining a prompt appointment to address my vehicle’s recall issue. Please advise me on the next steps I should take to resolve this matter. I appreciate your attention to this issue and look forward to your prompt response. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 23V707000 (ENGINE AND ENGINE COOLING). The contact stated while driving 15 MPH, the vehicle failed to accelerate as intended while depressing the accelerator pedal before the vehicle stalled. The Safe Mode message was displayed. The contact was driving uphill when the vehicle stalled. The contact helped to push the vehicle before coasting downhill. The vehicle was towed to a dealer where it was diagnosed and determined that the engine had seized. The vehicle was not repaired. The dealer stated that engine damage was not part of the recall. The manufacturer was made aware of the failure but offered no assistance. The vehicle remained at the dealer and had not been driven since the failure. The failure mileage was approximately 122,000.

The vehicle has been under recall for over a year and the fix is known and takes approximately 4 hours. BMW has had ample time to coordinate a repair, please enforce the repair for the vehicle.

I recently brought my 2011BMW 328i in for recalls and a shutter noise. My vehicle is equipped with the N51 SULEV motor. I recently was not able to set monitors for smog due to a shutter issue. I was told by a reliable mechanic it was the torque converter, and it is covered under the SULEV warranty. I was shocked when Bob told me that the torque converter was not covered under BMW SULEV warranty. It clearly states that in the SULEV warranty and my car only has 123,000 miles. He proceeded to call my car "a can of worms" and told me the technician simply does not want to work on my car. I know for a fact my Torque Converter and Mechatronik are covered under the SULEV warranty. I was simply kicked to the curb. This is unethical and my car is not passing smog due to this issue which is illegal. Please help resolve my issue.

Nothing has malfunctioned yet on the vehicle, however, these recalls are putting my daughter at risk while driving as there is an air bag and engine recall on the vehicle. Every time we contact the dealership, the recall is still unavailable.

Unknown

My car has the same issue as other BMW 328i made in 2011. however, when i put the vehicle vin number in my car does not pull up this as a recall. The Camshaft timing bolts are kicking off a check engine light. There is already a recall on this for other cars like mines see campaign 23V707000. Not sure what to do, any help would be greatly appreciated.

I had my car towed to BMW Northwest in fife on October 8th to have my recalled fixed for the vanos bolts that can cause engine problems. My car had shut down the day prior I couldn’t drive it. Through October 8 all the way till the 31st I had been in contact with BMW checking on the status of my car .. I have text messages between me and BMW about my car . I was told that 4 vanos bolts broke off into my engine and that bmw couldn’t find them they had to take my engine apart.. Then on October 31 I had got a call from BMW saying that they could not fix the the recall due to sludge on my engine, and that the reason that my engine had shut down was due to power maintenance . My car has all maintained regular oil change and kept up with the maintenance. So now BMW is trying to give me my car back with the Vanos bolt still stuck in the engine in my car not starting and they said they were not gonna fix the recall.

Recall for 2011 BMW 328i PCV Heater valve was conducted on or around March 12, 2023 at my local BMW private shop Bimmer Engineering located in Lancaster, CA. After service was performed was contacted by BMW representative that this service I paid out of pocket would be reimbursed, but would need to take to BMW dealership to be inspected to ensure BMW part had been replaced properly and with the authorized OME part manufactured by BMW. Vehicle was inspected at the Valencia BMW dealership on or around March 15, 2023 and verified manufactured part was replaced properly. After submitting a claim, letters, and invoices to BMW North America which concluded roughly a year later. I was informed that the reimbursement would not be honored due to recall not affiliated and TREAD ACT does not apply. This information was provided on or around October 11, 2024 by Executive Customer Care Relations and Services Specialist Kurt Westrich.

The contact owns a 2011 BMW 328I. The contact stated while driving 65 MPH, the vehicle stalled. The check engine warning light was illuminated. The contact was able to pull over to the shoulder of the roadway. The contact was able to restart the vehicle; however, the failure recurred several times while driving on the same day. Additionally, the contact stated while driving at various speeds and depressing the accelerator pedal, the vehicle shuddered and surged. The vehicle was taken to O'Reilly’s, where DTC code: P054B was retrieved; indicating a VANOS bolts failure. The vehicle was then taken to the dealer to be repaired under NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the dealer charged a diagnostic fee and informed the contact that the vehicle would need to be diagnosed for 2 hours prior to the recall repair. The contact declined to pay the diagnostic fee. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 129,000.

There is a Voluntary Safety Recalled #23V707 issued for my 2011 BMW 328i that deals with the Vanos Solenoid. My VIN is not included on this recall per website. My check engine light diagnosis shows a vanos solenoid issues. Dealership replaces vanos solenoid. Light comes back on, now the whole unit needs to be replaced. I separately went to a German mechanic and he communicated two times that my issue should be covered under the recall. How is this not associated with the safety recall issued in October 2023? Wouldn’t faulty bolts directly impact the engine and cause the whole unit problems? I feel terrified driving my car as I transport my elderly parents and fear for our safety.

The contact owns a 2011 BMW 328I. The contact received notifications of NHTSA Campaign Numbers: 24V513000 (AIR BAGS) and 23V707000 (ENGINE AND ENGINE COOLING); however, the parts to do the recall repairs were unavailable. The local dealer was contacted, and it was confirmed that the parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the air bag warning light remained illuminated while operating the vehicle. Additionally, the vehicle failed to immediately start, and while driving at an undisclosed speed, the check engine warning light flashed off and on. The cause of the failure was not yet determined. The failure mileage was 110,000. Parts distribution disconnect.

See attached document for complaint.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. The manufacturer was not made aware of the issue. Parts distribution disconnect.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V513000 (Air Bags); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2011 BMW 328I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated while driving approximately 35 MPH, the vehicle was losing motive power. The contact was unaware of any warning lights being illuminated. The contact stated that the vehicle stalled, and he was unable to be restarted. The contact had the vehicle towed to the residence. The vehicle was not taken to a dealer or an independent mechanic. The vehicle was not diagnosed or repaired. The failure mileage was approximately 90,000. Parts distribution disconnect.

Recall No. 23V-707 information from BMW North America was received in December 2023. No further communication or remedy has been provided by bmw. Per information letter, a compliant can be filed to nhtsa if bmw does not provide a remedy in a timely manner. Since it has been 9 months since this recall was issued and no timely fix from bmw, please follow up on this compliant with bmw. Thank you.

The contact owns a 2011 BMW 328I. The contact received notifications of NHTSA Campaign Numbers: 23V707000 (Engine and Engine Colling) and 24V513000 (Air Bags); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was able to restart; however, the failure recurred. The dealer was contacted; however, the vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 135,000. Parts distribution disconnect; for NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling). VIN tool confirms part not available; for NHTSA Campaign Number: 24V513000 (Air Bags).

Check engine light with code for timing error, Intake VANOS bolts are damaged are verified via visual inspection with a bore scope. Code P0012: Intake Camshaft Position Timing- Over-Retarded (Bank 1)

The contact owns a 2011 BMW 328I. The contact received notifications of NHTSA Campaign Numbers: 23V707000 (Engine and Engine Cooling) and 24V513000 (Air Bags); however, the parts to do the recall repairs were not yet available. The contact stated that while starting the vehicle and while driving at various speeds, the vehicle was shuddering. An unknown warning light was illuminated. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was unknown. VIN tool confirms parts not available.