Model T-2 hand-held electrical voltage and continuity testers
CPSC Recall #00-014 - November 8, 1999
Recall Summary
| Recall Number | 00-014 |
| Recall Date | November 8, 1999 |
| Remedy Type | Repair |
| Units Affected | About 58,000 |
Where It Was Sold
| Home centers |
| hardware stores and industrial distributors nationwide sold these testers between December 1997 and September 1999 for about $45. |
Product
Model T-2 hand-held electrical voltage and continuity testers
Description
WASHINGTON, D.C. - In cooperation with the U.S. Consumer Product Safety Commission (CPSC), Fluke Corp., of Everett, Wash., is voluntarily recalling about 58,000 model T-2 hand-held electrical voltage and continuity testers. The batteries in the tester could fail to maintain proper contact due to corrosion within the battery compartment, causing the device to lose power. Consumers testing electrical sources could fail to be warned of the presence of live current if the tester is not powered, posing a risk of shock, electrocution, and thermal burns.Fluke conducted a previous recall in November 1998 on T2 Electrical Testers because of a different electrical connection problem. Even if consumers had their testers repaired previously, their testers are part of this new recall and need to be repaired again.Fluke is aware of two incidents involving these testers where consumers received a mild electric shock.These testers measure 24 to 600 volts alternating current (VAC), and 6 to 220 volts direct current (VDC). "Fluke" and "T2" are written on the front of the unit. The tester body is yellow and black, and measures about 6.25 inches long by 1.75 inches wide and 1.25 inches thick. The wire leads are black and have one black and one red probe. Recalled units have a serial number lower than 74165430. The serial number is located on the back of the unit above the wire leads.Home centers, hardware stores and industrial distributors nationwide sold these testers between December 1997 and September 1999 for about $45.Consumers should stop using these voltage and continuity testers immediately, and contact Fluke to obtain a free repair kit or arrange to send your unit to Fluke for repair. For information on returning your unit to Fluke or obtaining a repair kit, consumers should call Fluke toll-free at (800) 753-8646 between 5 a.m. and 4 p.m. PT Monday through Friday. Consumers can access Fluke's website at www.fluke.com/whatsnew/ProductNotices/notices_99-10-01.asp.
Hazard
The batteries in the tester could fail to maintain proper contact due to corrosion within the battery compartment, causing the device to lose power. Consumers testing electrical sources could fail to be warned of the presence of live current if the tester is not powered, posing a risk of shock, electrocution, and thermal burns.
Incidents & Injuries
Fluke is aware of two incidents involving these testers where consumers received a mild electric shock.
Remedy Instructions
Consumers should stop using these voltage and continuity testers immediately, and contact Fluke to obtain a free repair kit or arrange to send your unit to Fluke for repair.
What Should You Do?
Stop using this product immediately. Contact the manufacturer for a Repair at no charge. If you experienced an injury, report it at SaferProducts.gov.
Frequently Asked Questions
Follow the consumer action instructions in the recall notice above. Most recalls require you to stop using the product and contact the manufacturer directly, either by calling the toll-free number listed in the official CPSC notice or by visiting the manufacturer's website. You generally do not need a receipt or original packaging to claim a remedy. The manufacturer is legally required to provide the remedy (Repair) at no cost to you.
If the product caused a fire or burn injury, document the incident with photos and preserve the product if it is safe to do so. Report the incident to the CPSC at SaferProducts.gov and to your local fire department. Contact the manufacturer to inform them of the incident, they are required to track and report injuries to CPSC. You may also want to consult a personal injury attorney, as fire and burn injuries caused by defective products can be grounds for a product liability claim against the manufacturer.
In most cases, no. CPSC-coordinated recall remedies are designed to be accessible without proof of purchase. Manufacturers typically ask consumers to self-certify ownership and may ask for photos of the product or its serial number. Some manufacturers request that you mail in a portion of the product (such as a cut cord or removed component) as proof of disposal. Check the specific remedy instructions for this recall for exact requirements. If you registered your product at the time of purchase, the process is usually even simpler.
If the original manufacturer has gone out of business, the recall remedy may no longer be available through them. In this case, contact CPSC directly at 1-800-638-2772 or cpsc.gov for guidance. If the brand was acquired by another company, the acquiring company may have assumed recall obligations. In some cases where a remedy is unavailable, CPSC advises consumers to safely dispose of the product. If you were injured by the product of a defunct company, consult a product liability attorney, parent companies, distributors, and retailers may still bear liability in some circumstances.