2009 HINO ND8J
3 recalls, 0 complaints - 57 TSBs
14V791000 Dec 15, 2014
PARKING BRAKE
Defect Description
Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain model year 2005-2015 Hino ND8J, NE8J, and NF8J trucks manufactured August 26, 2003, to May 14, 2014. In the affected vehicles, components of the parking brake handle assembly may wear, resulting in either the parking brake unexpectedly rele... Read more
Consequence
Either parking brake condition may result in the vehicle rolling unexpectedly, increasing the risk of a crash.
Remedy
Hino will notify owners, and dealers will install a new parking brake lever that contains a two-way damper and a roller at the cable joining pin, free of charge. The recall began February 2, 2015. Owners may contact Hino customer service at 1-248-699-9330. Hino's number for this recall is A9970. ... Read more
12V555000 Dec 3, 2012
ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES
Defect Description
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, NF8J, and NV8J, manufactured from August 18, 2003, through November 16, 2011. Over time, the main B+ circuit from the battery to the starter could potentially short to ground due to... Read more
Consequence
If the B+ circuit shorts to ground, it may lead to a fire.
Remedy
Hino will notify owners, and dealers will repair the vehicles free of charge. The recall began on January 17, 2013. Owners may contact Hino at 1-248-699-9390.
08V667000 Dec 18, 2008
SUSPENSION:REAR
Defect Description
HINO IS RECALLING 130 MY 2008-2009 ND8J, NE8J, NJ8J, AND NV8J CONVENTIONAL TRUCKS. THE REAR AXLE U-BOLTS WERE NOT PROPERLY TIGHTENED. THE LOWER SPRING SEAT MAY NOT CONTACT THE AXLE HOUSING PROPERLY, PRODUCING A GAP ON THE FRONT OR REAR SIDE OF THE AXLE HOUSING.
Consequence
THIS GAP COULD ALLOW THE U-BOLTS TO LOOSEN AND/OR CAUSE THE LOWER SPRING SEAT TO CRACK. THE AXLE COULD BECOME MISALIGNED AND/OR SEPARATED FROM THE MOUNTINGS INCREASING THE RISK OF A CRASH.
Remedy
DEALERS WILL INSPECT THE REAR AIR SUSPENSION LOWER SPRING SEAT FOR A GAP BETWEEN THE REAR AXLE AND LOWER SPRING SEAT. THE U-BOLTS WILL BE TIGHTENED TO THE SPECIFIED TORQUE. THE RECALL BEGAN ON JANUARY 19, 2009. OWNERS MAY CONTACT HINO AT 1-248-699-9330.
No complaints found for this vehicle.
Technical Service Bulletins, 2009 HINO ND8J
57 manufacturer communications from 36 unique bulletins. TSBs describe known problems and recommended fixes from the manufacturer.
Most Affected Components
| Component | Bulletins |
|---|---|
| 355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL | 8 |
| 060000 ENGINE (PWS) | 7 |
| 350000 EQUIPMENT | 6 |
| 090000 FUEL SYSTEM, OTHER | 4 |
| 356000 EQUIPMENT ADAPTIVE/MOBILITY | 4 |
| 092200 FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS | 3 |
| 070000 FUEL SYSTEM, GASOLINE | 3 |
| 060000 ENGINE AND ENGINE COOLING | 2 |
167-T1612-12
Oct 19, 2016
060000 ENGINE (PWS)
TT-16-013 The procedure for installing the rocker shaft bolts into the cam housing has been updated. It is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. The torque specifi
167-B0502-12
Sep 28, 2016
350000 EQUIPMENT
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B0502-12
Sep 28, 2016
190000 TIRES
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B0502-12
Sep 28, 2016
110000 ELECTRICAL SYSTEM
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B1621-12
Apr 18, 2016
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-16-010 Correction of the inspection of the DPR filter.
167-P1602-12
Mar 22, 2016
060000 ENGINE (PWS)
13-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified
167-P1602-12
Mar 22, 2016
072100 FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
13-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified
167-T1514-12
Jun 22, 2015
162000 STRUCTURE:BODY
TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
167-B1523-12
Jun 2, 2015
060000 ENGINE AND ENGINE COOLING
SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
167-B1312-12
Apr 13, 2015
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
167-B1521-12
Mar 17, 2015
020000 SUSPENSION
SB-15-022 In the rare event that a subject vehicle equipped with the 23k Comfort Ride air suspension experiences a premature main leaf failure, a 23k HD Comfort Ride air suspension may be installed with PRIOR APPROVAL from HMM QA.
167-B1516-12
Mar 6, 2015
063200 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
SB-15-017 New parts are available to prevent repeat exhaust manifold stud failures on the J05 engine. This bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. Modifications to
167-B1514-12
Feb 12, 2015
100000 POWER TRAIN
SB-15-015 Information of Troubleshooting Procedure for Engine Lacked Power during the DPR Automatic Regeneration
167-T1425-12
Nov 19, 2014
117000 ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
TT-14-029 A subject vehicle at 200,000 miles may exhibit a "DPR Maintenance" message displayed on the Instrument Cluster message center. The following procedure will instruct how to check the DPF and reset the displayed message.
SB-14-017
Sep 4, 2014
350000 EQUIPMENT
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
SB-14-017
Sep 4, 2014
100000 POWER TRAIN
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
SB-14-017
Sep 4, 2014
110000 ELECTRICAL SYSTEM
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
167-T1420-12
Aug 1, 2014
350000 EQUIPMENT
TT-14-021 This procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. Depending on the location of the repair, access may be limited in some cases. Ensure that the re
167-T1420-12
Aug 1, 2014
162800 STRUCTURE:BODY:HOOD
TT-14-021 This procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. Depending on the location of the repair, access may be limited in some cases. Ensure that the re
167-B1415-12
Mar 28, 2014
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-14-003 The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
RCB-010-12
Feb 21, 2014
061200 ENGINE AND ENGINE COOLING:ENGINE:DIESEL
HINO: THE ENGINE CONTROL PROGRAM COULD WORK IMPROPERLY, CAUSING CHECK ENGINE LIGHT (CEL) TO TURN ON, DUE TO AGING DEGRADATION OF FUEL INJECTOR AND SOOT ACCUMULATING IN DIESEL PARTICULATE FILTER (DPF). MODEL 2008-2010 NA6J, NB6J, NC6J, ND8
RCB-010-12
Feb 21, 2014
118000 ELECTRICAL SYSTEM:SOFTWARE
HINO: THE ENGINE CONTROL PROGRAM COULD WORK IMPROPERLY, CAUSING CHECK ENGINE LIGHT (CEL) TO TURN ON, DUE TO AGING DEGRADATION OF FUEL INJECTOR AND SOOT ACCUMULATING IN DIESEL PARTICULATE FILTER (DPF). MODEL 2008-2010 NA6J, NB6J, NC6J, ND8
167-B1101-12
Aug 10, 2011
090000 FUEL SYSTEM, OTHER
SB-11-002 REQUIREMENTS OF BIOFUEL USAGE FOR 2008MY THRU 2012MY VEHICLES ALL APPLIED MODELS
SB-09-001
Jun 15, 2009
030000 BRAKES (PWS)
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
SB-09-001
Jun 15, 2009
070000 FUEL SYSTEM, GASOLINE
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
SB-09-001
Jun 15, 2009
070000 FUEL SYSTEM, GASOLINE
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
SB-09-001
Jun 15, 2009
350000 EQUIPMENT
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
SB-09-001
Jun 15, 2009
356000 EQUIPMENT ADAPTIVE/MOBILITY
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
SB-09-001
Jun 15, 2009
060000 ENGINE (PWS)
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be t
LT-0010
Jun 1, 2009
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
Hino Quick Reference Guide 2005-2010 Model Years
SB-R-0034
Mar 3, 2009
073200 FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
HINO TRUCKS: ABNORMAL NOISE AND VIBRATION WITHIN THE ENGINE OCCURS DUE TO THE IMPEDED OPERATION OF THE INJECTOR NEEDLE WHICH IS CAUSED BY THE FORMATION OF DEPOSITS IN THE FUEL. *PE
SB-R-0033
Mar 3, 2009
090000 FUEL SYSTEM, OTHER
HINO TRUCK: THE DAVCO FUEL FILTER ASSEMBLY HAS BEEN IMPROVED TO PREVENT THE EFFUSION OF AIR INTO THE FUEL SYSTEM. *PE
SB-R-0034
Mar 3, 2009
061000 ENGINE AND ENGINE COOLING:ENGINE
HINO TRUCKS: ABNORMAL NOISE AND VIBRATION WITHIN THE ENGINE OCCURS DUE TO THE IMPEDED OPERATION OF THE INJECTOR NEEDLE WHICH IS CAUSED BY THE FORMATION OF DEPOSITS IN THE FUEL. *PE
SB-R-0030
Mar 3, 2009
092200 FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
HINO TRUCK: ABNORMAL NOISE AND VIBRATION WITHIN THE ENGINE OCCURS DUE TO THE IMPEDED OPERATION OF THE INJECTOR NEEDLE WHICH IS CAUSED BY THE FORMATION OF DEPOSITS IN THE FUEL. *PE
SB-R-0030
Mar 3, 2009
090000 FUEL SYSTEM, OTHER
HINO TRUCK: ABNORMAL NOISE AND VIBRATION WITHIN THE ENGINE OCCURS DUE TO THE IMPEDED OPERATION OF THE INJECTOR NEEDLE WHICH IS CAUSED BY THE FORMATION OF DEPOSITS IN THE FUEL. *PE
SB-R-0029
Mar 3, 2009
092200 FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
HINO TRUCKS: THE FUEL TANK BREATHER HOSE(S) HAS BEEN MODIFIED TO PREVENT WATER FROM ENTERING INTO THE FUEL TANK(S). *PE
SL-R-0031
Mar 3, 2009
092200 FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
HINO TRUCKS: ABNORMAL NOISE AND VIBRATION WITHIN THE ENGINE OCCURS DUE TO THE IMPEDED OPERATION OF THE INJECTOR NEEDLE WHICH IS CAUSED BY THE FORMATION OF DEPOSITS IN THE FUEL. *PE
167-B0803-12
Dec 5, 2008
203000 WHEELS:LUGS/NUTS/BOLTS/STUDS
SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
SB-08-004
Aug 28, 2008
070000 FUEL SYSTEM, GASOLINE
This document is to inform dealers and workshops of the design change to the supply pump and SCV for J08E-TV, TW engine series.
SB-08-004
Aug 28, 2008
356000 EQUIPMENT ADAPTIVE/MOBILITY
This document is to inform dealers and workshops of the design change to the supply pump and SCV for J08E-TV, TW engine series.
SB-08-004
Aug 28, 2008
350000 EQUIPMENT
This document is to inform dealers and workshops of the design change to the supply pump and SCV for J08E-TV, TW engine series.
SB-08-003
Aug 27, 2008
090000 FUEL SYSTEM, OTHER
This document is to inform dealers and work shops to the update of inlet and outlet fuel pipes on the Davco fuel filter assembly.
SB-08-003
Aug 27, 2008
350000 EQUIPMENT
This document is to inform dealers and work shops to the update of inlet and outlet fuel pipes on the Davco fuel filter assembly.
SB-08-003
Aug 27, 2008
356000 EQUIPMENT ADAPTIVE/MOBILITY
This document is to inform dealers and work shops to the update of inlet and outlet fuel pipes on the Davco fuel filter assembly.
167-P0803-12
Mar 5, 2008
060000 ENGINE (PWS)
PTB 01-08 Complete Engine Assembly Part Numbers
167-T0706-12
Jun 28, 2007
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
07 - 006 VOLTAGE DROP TEST
167-B0602-12
Sep 18, 2006
061320 ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
167-B0601-12
Jul 10, 2006
060000 ENGINE AND ENGINE COOLING
SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
167-B0501-12
Nov 20, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0501-12
Nov 20, 2005
060000 ENGINE (PWS)
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0503-12
Nov 4, 2005
060000 ENGINE (PWS)
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) R
167-B0505-12
Nov 4, 2005
356000 EQUIPMENT ADAPTIVE/MOBILITY
SB ? 05 - 007 DESIGN CHANGE OF WATER PIPE FOR J08E
167-B0506-12
Nov 4, 2005
060000 ENGINE (PWS)
SB ? 05 - 008 This document is to inform the dealers about the addition of the pressure sensor cover and related part for the J08E engine.
167-B0503-12
Nov 4, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) R
167-B0508-12
Sep 28, 2005
106000 POWER TRAIN:AXLE ASSEMBLY
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0508-12
Sep 28, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0504-12
Sep 27, 2005
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
HINO ND8J - All Years Overview
Complete safety history for the HINO ND8J across all model years (2005, 2015).
44
Total Recalls
0
Total Complaints
0
Investigations
0
Reported Crashes
0
Reported Fires
0
Reported Deaths