2012 HINO NJ8J
4 recalls, 0 complaints - 79 TSBs
19V044000 Jan 18, 2019
SERVICE BRAKES
Defect Description
Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2007-2019 NJ8J (258ALP) vehicles. These vehicles do not have dust shields on the front brake assemblies. During wet conditions, uneven water saturation on the front brake assemblies may result in the vehicle pulling to the left during hard... Read more
Consequence
If the vehicle pulls left, it may cross into another lane unexpectedly, increasing the risk of crash.
Remedy
Hino will notify owners, and dealers will install new brake drums with dust shields, free of charge. The recall began March 19, 2019. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AACL0.
17V607000 Sep 28, 2017
ENGINE AND ENGINE COOLING:ENGINE:DIESEL
Defect Description
Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain 2011-2012 NE8J, NJ8J, and NV8J trucks. The engines have a wrist pin bushings in the connecting rods that may shift and cause excessive cylinder wear.
Consequence
Excessive wear of the cylinders can result in engine failure, increasing the risk of a crash.
Remedy
Hino will notify owners, and dealers will inspect and, as necessary, replace the connecting rods. Interim notices informing owners of the safety risk were mailed November 27, 2017. The recall began on March 19, 2018. Owners may contact Hino customer service at 1-248-699-9300. Hino's number for t... Read more
12V555000 Dec 3, 2012
ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES
Defect Description
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, NF8J, and NV8J, manufactured from August 18, 2003, through November 16, 2011. Over time, the main B+ circuit from the battery to the starter could potentially short to ground due to... Read more
Consequence
If the B+ circuit shorts to ground, it may lead to a fire.
Remedy
Hino will notify owners, and dealers will repair the vehicles free of charge. The recall began on January 17, 2013. Owners may contact Hino at 1-248-699-9390.
11V537000 Nov 3, 2011
POWER TRAIN:AXLE ASSEMBLY
Defect Description
HINO IS RECALLING CERTAIN MODEL 2012 ND8J, NE8J, NJ8J, AND NV8J COMMERCIAL TRUCKS MANUFACTURED FROM JULY 25, 2011, THROUGH SEPTEMBER 16, 2011. DURING ASSEMBLY, THE WHEEL-END RETAINER ON THE FRONT OR REAR AXLE MAY HAVE BEEN INSTALLED INCORRECTLY.
Consequence
THE WHEEL-HUB AND AXLE SHAFT CAN SEPARATE FROM THE VEHICLE, POSSIBLY RESULTING IN A CRASH.
Remedy
HINO WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE FRONT AXLE ASSEMBLIES AND, IF THE AXLE IS FOUND TO BE INCORRECTLY ASSEMBLED, DEALERS WILL REPLACE THE WHEEL END RETAINING HARDWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 19, 2012. OWNERS MAY CONTACT HINO AT 1-248-699-9390.
No complaints found for this vehicle.
Technical Service Bulletins, 2012 HINO NJ8J
79 manufacturer communications from 52 unique bulletins. TSBs describe known problems and recommended fixes from the manufacturer.
Most Affected Components
| Component | Bulletins |
|---|---|
| 355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL | 13 |
| 350000 EQUIPMENT | 10 |
| 118000 ELECTRICAL SYSTEM:SOFTWARE | 5 |
| 063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM | 5 |
| 110000 ELECTRICAL SYSTEM | 5 |
| 356000 EQUIPMENT ADAPTIVE/MOBILITY | 4 |
| 060000 ENGINE (PWS) | 4 |
| 061610 ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE | 3 |
167-B1904-01
Apr 11, 2019
030000 SERVICE BRAKES, HYDRAULIC
SA-19-011 AACL0 CONVENTIONAL ALP DRUM AND DUST SHIELD PROCEDURE CHANGES
167-B1426-12
Nov 4, 2016
162810 STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS
SA-14-026 The broken hood grille procedure (SB-14-020) has been revised to reuse the grille nuts (SZ17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
167-B0502-12
Sep 28, 2016
110000 ELECTRICAL SYSTEM
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B0502-12
Sep 28, 2016
350000 EQUIPMENT
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B0502-12
Sep 28, 2016
190000 TIRES
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B1625-12
Aug 5, 2016
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-16-021 CORRECTION OF WORKSHOP MANUAL FOR HINO600 SERIES Correction of Electrical Wiring Diagram
167-B1621-12
Apr 18, 2016
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-16-010 Correction of the inspection of the DPR filter.
167-P1602-12
Mar 22, 2016
072100 FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
13-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified
167-P1602-12
Mar 22, 2016
060000 ENGINE (PWS)
13-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified
167-B1529-12
Oct 21, 2015
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-15-032 Troubleshooting information and Inspection procedure of the DTC/P2030 were revised.
167-B1528-12
Aug 26, 2015
353000 EQUIPMENT:ELECTRICAL
SB-15-031 Foreign debris in the DEF (Diesel Exhaust Fluid) tank may cause the SCR (Selective Catalyst Reduction) system to malfunction. This can result in DTC?s (Diagnostic Trouble Codes) P20E8 or P20E9 - DEF Pressure Abnormality. An inlet
167-T1514-12
Jun 22, 2015
162000 STRUCTURE:BODY
TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
167-B1523-12
Jun 2, 2015
060000 ENGINE AND ENGINE COOLING
SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
167-T1513-12
Apr 22, 2015
100000 POWER TRAIN
TT-15-014 The transmission DTC?s P0974 and P0986, may be found on 12MY-15MY COE models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case an
167-B1312-12
Apr 13, 2015
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
167-B1521-12
Mar 17, 2015
020000 SUSPENSION
SB-15-022 In the rare event that a subject vehicle equipped with the 23k Comfort Ride air suspension experiences a premature main leaf failure, a 23k HD Comfort Ride air suspension may be installed with PRIOR APPROVAL from HMM QA.
167-B1511-12
Feb 4, 2015
011000 STEERING: STEERING WHEEL/HANDLE BAR
SB-15-011 The following TSB (Technical Service Bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
167-B1510-12
Jan 20, 2015
063130 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
SB-15-010 Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated E
167-B1504-12
Jan 9, 2015
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-15-003 CORRECTION OF WORKSHOP MANUAL FOR HINO 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P0421)
167-B1503-12
Jan 9, 2015
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-15-002 CORRECTION OF WORKSHOP MANUAL FOR 2013 - 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P2123)
TT-14-033
Dec 5, 2014
061500 ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION
When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
TT-14-033
Dec 5, 2014
350000 EQUIPMENT
When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
SB-14-020
Sep 22, 2014
356000 EQUIPMENT ADAPTIVE/MOBILITY
When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
SB-14-020
Sep 22, 2014
350000 EQUIPMENT
When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
SB-14-020
Sep 22, 2014
162810 STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS
When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
SB-14-016
Sep 8, 2014
036400 SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
SB-14-016
Sep 8, 2014
100000 POWER TRAIN
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
SB-14-016
Sep 8, 2014
110000 ELECTRICAL SYSTEM
In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating
SB-14-014
Jul 25, 2014
350000 EQUIPMENT
Subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not complete.
SB-14-014
Jul 25, 2014
061610 ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE
Subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not complete.
SB-14-013
Jul 23, 2014
350000 EQUIPMENT
DPR damage, "Burner misfire due to excessive soot on the burner igniter surface", and "DPR push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
SB-14-013
Jul 23, 2014
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
DPR damage, "Burner misfire due to excessive soot on the burner igniter surface", and "DPR push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
SB-14-013
Jul 23, 2014
070000 FUEL SYSTEM, GASOLINE
DPR damage, "Burner misfire due to excessive soot on the burner igniter surface", and "DPR push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
SB-14-013
Jul 23, 2014
061610 ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE
DPR damage, "Burner misfire due to excessive soot on the burner igniter surface", and "DPR push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
TT-14-016
Jun 27, 2014
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
Exhaust Combustion Chamber with Loose Insulation
TT-14-016
Jun 27, 2014
350000 EQUIPMENT
Exhaust Combustion Chamber with Loose Insulation
TT-14-016
Jun 27, 2014
356000 EQUIPMENT ADAPTIVE/MOBILITY
Exhaust Combustion Chamber with Loose Insulation
TT-14-017
Jun 27, 2014
040000 SERVICE BRAKES, AIR
Bendix? Air Dryer Service
TT-14-017
Jun 27, 2014
350000 EQUIPMENT
Bendix? Air Dryer Service
167-T1415-12
Jun 27, 2014
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
TT-14-016 During service of the exhaust aftertreatment system, the technician may visually find that the insulation within the outer shell of the combustion chamber is pushing out or loose. In the event that loose insulation is found, it is
167-B1423-12
Jun 19, 2014
353000 EQUIPMENT:ELECTRICAL
SB-14-005 2011MY-2015MY Conventional Keyless Entry Programming
167-B1423-12
Jun 19, 2014
118000 ELECTRICAL SYSTEM:SOFTWARE
SB-14-005 2011MY-2015MY Conventional Keyless Entry Programming
167-B1415-12
Mar 28, 2014
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB-14-003 The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
TSB-14-025
Feb 5, 2014
350000 EQUIPMENT
Subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous DTC?s (Diagnostic Trouble Codes) setting i
TSB-14-025
Feb 5, 2014
110000 ELECTRICAL SYSTEM
Subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous DTC?s (Diagnostic Trouble Codes) setting i
167-A1401-12
Jan 22, 2014
061320 ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
A-15-008 A subject vehicle may experience DPR (Diesel Particulate Reduction) system related issues in extreme cold weather conditions. If a good fuel quality is being used and persistent fuel gelling has been confirmed to be the cause of t
SB-15-010
Jan 20, 2014
356000 EQUIPMENT ADAPTIVE/MOBILITY
Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated EGR valve h
SB-15-010
Jan 20, 2014
350000 EQUIPMENT
Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated EGR valve h
SB-15-010
Jan 20, 2014
063130 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated EGR valve h
14-002
Jan 9, 2014
350000 EQUIPMENT
COE HYBRID SAFETY EQUIPMENT, TOOLS AND PRACTICES
14-002
Jan 9, 2014
110000 ELECTRICAL SYSTEM
COE HYBRID SAFETY EQUIPMENT, TOOLS AND PRACTICES
14-002
Jan 9, 2014
062000 ENGINE AND ENGINE COOLING:COOLING SYSTEM
COE HYBRID SAFETY EQUIPMENT, TOOLS AND PRACTICES
167-B1307-12
Jul 23, 2013
103300 POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
13-008 Design Change of the Idler Gear Case and Idler Gear Bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idle
167-T1303-12
Jun 21, 2013
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
13-003 Injection Quantity Test 11 thru 14MY
RCB-002-13
May 31, 2013
118000 ELECTRICAL SYSTEM:SOFTWARE
HINO TRUCKS: MALFUNCTION INDICATOR LAMP (MIL) MAY BE ILLUMINATING. VEHICLE MAY ALSO EXPERIENCE REDUCED POWER. PERFORMING A SOFTWARE ENHANCEMENT SHOULD CORRECT THIS PROBLEM. *KB
RCB-001-13
Mar 1, 2013
061200 ENGINE AND ENGINE COOLING:ENGINE:DIESEL
HINO: SOOT ACCUMULATES ON THE IGNITER. BURNER IGNITION COULD PERFORM IMPROPERLY. REPLACEMENT OF THE DIESEL PARTICULATE REGENERATION (DPR) IGNITER PLUGS. *KB
RCB-001-13
Mar 1, 2013
116000 ELECTRICAL SYSTEM:IGNITION
HINO: SOOT ACCUMULATES ON THE IGNITER. BURNER IGNITION COULD PERFORM IMPROPERLY. REPLACEMENT OF THE DIESEL PARTICULATE REGENERATION (DPR) IGNITER PLUGS. *KB
RCB-008-12
Jan 11, 2013
118000 ELECTRICAL SYSTEM:SOFTWARE
HINO TRUCKS: MALFUNCTION INDICATOR LAMP (MIL) POSSIBLY ILLUMINATING DURING COLD TEMPERATURES. SOFTWARE UPDATE FOR THE DOSING CONTROL UNIT (DCU) COULD SOLVE THIS PROBLEM. *KB
RCB-009-12
Jan 11, 2013
118000 ELECTRICAL SYSTEM:SOFTWARE
HINO: SOFTWARE UPDATE FOR BURNER CONTROL UNIT (BCU). IGNITION OF THE BURNER SYSTEM MAY PERFORM IMPROPERLY AND CAUSE A MIL LIGHT TO ILLUMINATE IN THE INSTRUMENT CLUSTER. *KB
HINO 12-004
Dec 12, 2012
061610 ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE
SUBJECT VEHICLES:
HINO 12-004
Dec 12, 2012
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
SUBJECT VEHICLES:
167-T1204-12
Oct 11, 2012
062000 ENGINE AND ENGINE COOLING:COOLING SYSTEM
12 - 002 Diagnosis Procedure for P2457. Some engines may erroneously record a P2457 DTC in the ECU. This fault condition is due to ECU software misdetection of EGR cooler efficiency.
HINO 12-003 TT
Oct 11, 2012
110000 ELECTRICAL SYSTEM
This Tech Tip pertains to 2012 NE8J, NJ8J, NV8J Models that have ECU software 89663-E2B40A or 89663-E2B50A. Some engines may erroneously record P2457 DTC in ECU. This fault condition is due to ECU software misdetection of EGR cooler effi
167-T1204-12
Oct 11, 2012
118000 ELECTRICAL SYSTEM:SOFTWARE
12 - 002 Diagnosis Procedure for P2457. Some engines may erroneously record a P2457 DTC in the ECU. This fault condition is due to ECU software misdetection of EGR cooler efficiency.
167-T1202-12
Oct 4, 2012
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
12-001 Recording the Burner Event Log (BEL) on 11-13MY Trucks
167-B1101-12
Aug 10, 2011
090000 FUEL SYSTEM, OTHER
SB-11-002 REQUIREMENTS OF BIOFUEL USAGE FOR 2008MY THRU 2012MY VEHICLES ALL APPLIED MODELS
167-B0803-12
Dec 5, 2008
203000 WHEELS:LUGS/NUTS/BOLTS/STUDS
SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-T0706-12
Jun 28, 2007
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
07 - 006 VOLTAGE DROP TEST
167-B0602-12
Sep 18, 2006
061320 ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
167-B0601-12
Jul 10, 2006
060000 ENGINE AND ENGINE COOLING
SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
167-B0501-12
Nov 20, 2005
060000 ENGINE (PWS)
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0501-12
Nov 20, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0506-12
Nov 4, 2005
060000 ENGINE (PWS)
SB ? 05 - 008 This document is to inform the dealers about the addition of the pressure sensor cover and related part for the J08E engine.
167-B0505-12
Nov 4, 2005
356000 EQUIPMENT ADAPTIVE/MOBILITY
SB ? 05 - 007 DESIGN CHANGE OF WATER PIPE FOR J08E
167-B0503-12
Nov 4, 2005
060000 ENGINE (PWS)
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) R
167-B0503-12
Nov 4, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) R
167-B0508-12
Sep 28, 2005
355200 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0508-12
Sep 28, 2005
106000 POWER TRAIN:AXLE ASSEMBLY
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0504-12
Sep 27, 2005
063000 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
HINO NJ8J - All Years Overview
Complete safety history for the HINO NJ8J across all model years (2005, 2021).
59
Total Recalls
0
Total Complaints
0
Investigations
0
Reported Crashes
0
Reported Fires
0
Reported Deaths
HINO NJ8J - Year by Year
Compare recalls and complaints across model years. Click any year to see full details.