Showing 252,439 complaints for CHEVROLET
Incident date: Mar 4, 2026
I was driving to work on the freeway about 65 mph and after about 20 minutes the engine made a whirring noise, overheating and slight smell of burnt rubber and delayed to Accelerate luckily I was close to my exit I parked vehicle let it cool down. But still has this issue after about 20-30 minutes of driving more than 60mph
Incident date: Mar 4, 2026
The ICCU on the car failed and blew a fuse. KIA had to replace ICCU and fuse under warranty
Incident date: Mar 13, 2026
MY GIRLFRIEND ALMOST CRASHED GOING DOWN A HILL TOWARD A STOP SIGN FOR A BUSY INTERSECTION FOR A ROAD THAT IS ALONG A CLIFFSIDE. JEEP CANNOT GET A PART FOR THIS VEHICLE AFTER NUMEROUS ATTEMPTS TO GET ONE. NEEDS AN ABS MODULE AS ONE OF THE WHEEL SPEED SENSOR CIRCUITS IS NOT COMMUNICATING. I HAVE REACHED OUT TO MULTIPLE MODULE REBUILDERS AND THEY ARE UNABLE TO GET PARTS FOR THIS MODULE ANYMORE. THIS
... IS A WELL-KNOWN ISSUE WITH THE WRANGLERS AND JEEP IS NOT WILLING TO RELEASE A RECALL TO MAKE IT RIGHT. DUE TO PARTS SHORTAGE, THE MODULES ARE GOING ONLINE FOR $1500-$2000, WHICH FOR A MAJOR SAFETY COMPONENT CAN BE A LARGE ISSUE. WE HAVE SINCE PARKED THE VEHICLE FOR THE PAST 3 MONTHS WHILE I ATTEMPT TO LOCATE A REASONABLY PRICED MODULE OR FIND SOMEBODY THAT HAS THE CHIPS/CAPACITORS TO REBUILD IT. I AM A DEALERSHIP TECHNICIAN WITH 7 YEARS OF EXPERIENCE AND WE HAVE SENT LOTS OF THESE VEHICLES TO AUCTION FOR THE SAME CONCERN.Read more
Incident date: Mar 13, 2026
At highway speeds, steering wheel seems to get stuck with minor corrections, then suddenty "gives way" causing a dangerous overcorrection which alters the course of the vehicle. Vehicle does not have lane-keeping technology. Widely reported on 10th gen civic forums, i'm not alone.
Incident date: Mar 9, 2026
Beginning at 9000 miles, clicking began when taking right and left turns. I have had 8 axle replacements and still the issue is not repaired.
Incident date: Mar 9, 2026
The vehicle shifted itself into neutral and shut off while driving. It happened twice in three days. The first time I was pulling into the driveway so I was able to put it in park and restart the car safely. The second time I was in the middle of traffic in Tampa and it shifted into neutral and shut off in the middle of the road. Luckily no cars hit me but again I had to apply the break , restart
... the car and put it back in drive. This was very scary and I had my kids with me. Earlier in the day I had been driving on 75 and if it had happened then it could have been a bad wreck. It shows there are no current recalls on my vehicle. No warning lights or messages appeared. Vehicle was purchased less than 30 days ago. I will contact the dealership to verify there are no open recalls just in case but again when I checked I found none.Read more
Incident date: Jan 4, 2024
The contact owns a 2013 Ford C-Max Hybrid. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate as intended while depressing the accelerator pedal. The message "Stop Safely Now'" was displayed on the screen. The contact was able to pull to the side of the road. However, no cause for the failure was found. The vehicle was not repaired. The contact stated t
... hat on a separate occasion, while driving at an undisclosed speed, the vehicle failed to accelerate as intended while depressing the accelerator pedal. The vehicle was taken to the dealer; however, no cause for the failure was found. The failure persisted. The vehicle failed to accelerate as intended while depressing the accelerator pedal, and the vehicle stalled. The message "Stop Safely Now'" was displayed on the screen. The contact was able to coast to the side of the road. After waiting for several minutes, the contact was able to restart the vehicle. The vehicle functioned as intended. The vehicle was towed to the dealer; however, no cause for the failure was found. The contact stated that the failure first occurred three years ago, and the dealer diagnosed that it as a battery failure. The contact was unsure if the battery was replaced. The manufacturer was notified of the failure but offered no assistance. The failure mileage was approximately 107,000.Read more
Incident date: Mar 13, 2026
Airbags sistem failed
Incident date: Jan 26, 2026
The contact owns a 2016 Chevrolet Silverado 1500. The contact stated while driving at an undisclosed speed, the transmission was slipping. There was no warning light illuminated. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 120,000.
Incident date: Dec 31, 2001
I found a lot of shaved metals when I did the oil change for the Gear Reduction. It made a lot of noises when driving or the wheel of fortune sounds whether the car is in Regenerative Braking. The sounds developed as time goes on but Hyundai failed to recall this issue. I found this has been an ongoing issue since 2019 when Hyundai make this Kona EV, but their engineers didn’t fix this type of
... issue and continue to manufacture the Kona EV with the same Gear Reduction Assembly and it caused a lot of noises with these shaving metals found in the oil changes. This is abnormal for a GRU to have so many metals found in the oil. Thus, it made a lot of noises. Now my car can’t even drive because of this. The GRU has been broken because of this issue that Hyundai didn’t even fix since 2019.Read more
Incident date: Dec 31, 2001
The transmission on the vehicle failed. It is available for inspection. The vehicle began jolting, when accelerating from a stop, or when slowing to a stop. Seemed to be slipping out of gear while driving. We reported the incident to the dealership. They said they found nothing wrong. The issue continued, and the check engine light came on, so we returned to the dealer again. This time they foun
... d it needed the transmission to be rebuilt. They have had the car at the service center for 5 months. The parts they need are no longer available.Read more
Incident date: May 11, 2025
The contact owns a 2019 Honda Accord. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly went into LIMP Mode, with several unknown warning lights illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed with fuel pump failure. The contact was informed that the fuel pump needed to be replaced. The vehicle was not repaired. The vehicl
... e was then taken to the dealer but was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.Read more
Incident date: Mar 9, 2026
The ACC is failing in the car. It is due to a faulty radar sensor located behind the rear view mirror that according to the dealership gets to hot it the sun and begins to deteriorate.
Incident date: Mar 9, 2026
The ACC is failing in the car. It is due to a faulty radar sensor located behind the rear view mirror that according to the dealership gets to hot it the sun and begins to deteriorate.
Incident date: Feb 15, 2026
I have a 2024 INEOS Grenadier with the factory installed Tow Package. While the Grenadier does not offer an Electric Brake Controller as an an option, they do market the vehicle as being pre-wired to accept aftermarket controller thereby allowing the vehicle to pull the maximum tow weight of 7600 pounds. The problem is the wiring does not conform to US requirements with regard to the brake signal
... trigger and as a result it is not possible to activate the brake controller. This is a known manufacturing defect affecting every Grenadier sold in the US. I have contacted INEOS regarding this matter and this is their reply: Hi [XXX] , Thanks for contacting INEOS Automotive. I have heard back from the relevant team and our team are aware of the issue. Unfortunately there was no ETA given for this but there are plans to look into this issue further. Please don't hesitate to contact us for any further assistance. Best regards, INEOS Automotive Customer Care Team This is not an acceptable response for addressing a manufacturing defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)Read more
Incident date: Mar 6, 2026
Have had A/C issues for years, have had to replace compressor and condenser 4 times, only twice after a warranty finally came out for the defective parts. Now, the evaporator core has failed, but it is not under extended warranty or recall. Wild as I've seen so many with issues with another part of the faulty a/c system, likely from a defect. Going through a heatwave currently, dropping 3K on an e
... vaporator core was not on my budget, especially when I believe Honda is at fault here. Tried a goodwill claim with them, immediately rejected. This came shortly after the condenser and shaft were replaced at the dealership.Read more
Incident date: Dec 30, 2025
The contact owns a 2014 Mercedes-Benz ML63 AMG. The contact stated that the vehicle was experiencing front suspension, coolant, and oil leak failures. The contact stated that the front suspension unexpectedly lowered while the vehicle was parked or while driving. The message "Active Curve System Malfunction" was displayed. The vehicle was towed to the dealer, where unknown repairs were performed.
... Additionally, the contact noticed a coolant leak in the garage, where the vehicle was parked. The vehicle was taken to two certified independent mechanics, where unknown repairs were performed; however, the failure recurred. The vehicle was taken to the dealer, where the seals were inspected and corrected, and it was diagnosed that the front left cylinder and the lower and upper radiator hoses were leaking. Additionally, a leak was found at the firewall connection. The vehicle was repaired; however, the failure recurred. The vehicle was taken back to the dealer, where the same assessment was made, and the vehicle was repaired; however, the failure persisted. The contact stated while at a complete stop at the red traffic light, the vehicle stalled and failed to restart. The vehicle was pushed into a parking lot with assistance. A warning light for key fob battery drainage was illuminated. The vehicle was towed to an independent mechanic, where the failure was related to an unknown recall, and the contact was referred to the dealer. The contact stated that the dealer had previously completed the repair of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline); however, the recall repair had failed to fix the vehicle. The vehicle recently stalled and was towed to the dealer, where it remained. The vehicle was not repaired. The manufacturer was notified of the failure, and the case was escalated to an Executive. The failure mileage was approximately 100,000.Read more
Incident date: Nov 19, 2025
Infotainment system freezes and goes black. Braking system makes popping and clicking noises and have to press hard to stop the vehicle. Vehicle has been in the shop now 5 times and over 30+ days. The braking system failure has put my safety and others at risk to due to not being able to brake correctly.
Incident date: Mar 8, 2026
The contact owns a 2007 Chevrolet Silverado 1500. While driving at an undisclosed speed, there was an abnormal, pungent odor coming from the vehicle. The contact was unsure if any warning lights were illuminated. On a separate occasion, the vehicle drove roughly with an abnormal sound coming from the engine. Additionally, the engine was consuming an excessive amount of engine oil. The contact had
... to add seven quarts of oil for every 3,000 miles driven. The vehicle was towed to an independent mechanic who diagnosed that the Active Fuel Management (AFM) system had failed. The engine was replaced. The manufacturer was not made aware of the failure. The failure mileage was unknown.Read more
Incident date: Mar 12, 2026
The contact owns a 2006 Dodge Caravan. The contact stated that the horn was inoperable, and the air bag warning light was illuminated. The dealer was contacted and informed the contact that the VIN was not included in the related undisclosed recall. The vehicle was not diagnosed or repaired due to the cost. The contact was referred to the NHTSA Hotline for assistance. The manufacturer was not cont
... acted. The failure mileage was approximately 198,000.Read more
Incident date: Mar 12, 2026
Unintended acceleration, on 2 occasions. First occasion, car was in DRIVE waiting at a traffic stop and the engine radically increased it's RPM from idle to over 6000 RPM, remaining there. Braking control maintained the automobile's position. Shifting the car into neutral caused RPM to increase further. The car was shut off, restarted, and seemed to function normally. On the second occasion, whi
... ch occurred later the same day, the car was off and then started, and while still in PARK with my foot on the brake immediately jumped to over 6000, remaining there. Once again the car was shut off, restarted, and seemed to work normally. It was taken directly (and slowly) to the manufacturer's service center at my local Subaru dealership. They have not been able to re-create the problem as of this date.Read more
Incident date: Mar 12, 2026
Unintended acceleration, on 2 occasions. First occasion, car was in DRIVE waiting at a traffic stop and the engine radically increased it's RPM from idle to over 6000 RPM, remaining there. Braking control maintained the automobile's position. Shifting the car into neutral caused RPM to increase further. The car was shut off, restarted, and seemed to function normally. On the second occasion, whi
... ch occurred later the same day, the car was off and then started, and while still in PARK with my foot on the brake immediately jumped to over 6000, remaining there. Once again the car was shut off, restarted, and seemed to work normally. It was taken directly (and slowly) to the manufacturer's service center at my local Subaru dealership. They have not been able to re-create the problem as of this date.Read more
Incident date: Mar 6, 2026
The driver’s seat in my 2017 Subaru Forester suddenly became loose and moves left to right while driving. The vehicle has only 27,000 miles, has never been in an accident, and has been meticulously maintained. The Subaru dealer diagnosed failed seat frame rail guides and replaced the entire seat undercarriage at a cost of $1,742 because the guides cannot be replaced individually. The dealer stat
... ed they had never seen this failure before. Because the seat moves laterally while driving, I believe this represents a potential safety defect.Read more
Incident date: Mar 6, 2026
Both the driver side and passenger side exterior a-pillar applique molding came while driving down the highway and almost caused an accident. This has happened twice because FORD says they can't fix it because they don't have the parts. Anyone can get the parts online that are after market but that does not fix the issue. I did buy the after market ones and those came off on the interstate and al
... most hit a motorcycle driver. This has been going on Since January of 2024 and FORD is not doing anything about it. You are unable to call FORD, email FORD, and no one will escalate this. Now it has become even more of a safety issues because my rubber seals for my windshield are wearing and tearing off at a fast pace. It is causing more damage that FORD will not be responsible for fixing. Why do safety recalls not get fixed and are not forced to be fixed? Safety recall and no one cares to get it fixed.Read more
Incident date: Mar 6, 2026
Both the driver side and passenger side exterior a-pillar applique molding came while driving down the highway and almost caused an accident. This has happened twice because FORD says they can't fix it because they don't have the parts. Anyone can get the parts online that are after market but that does not fix the issue. I did buy the after market ones and those came off on the interstate and al
... most hit a motorcycle driver. This has been going on Since January of 2024 and FORD is not doing anything about it. You are unable to call FORD, email FORD, and no one will escalate this. Now it has become even more of a safety issues because my rubber seals for my windshield are wearing and tearing off at a fast pace. It is causing more damage that FORD will not be responsible for fixing. Why do safety recalls not get fixed and are not forced to be fixed? Safety recall and no one cares to get it fixed.Read more
Incident date: Apr 1, 2025
The contact owns a 2017 Hyundai Sonata. The contact stated that while his wife was driving at an undisclosed speed, the vehicle experienced engine failure. The vehicle made a knocking sound prior to the failure. No warning lights were illuminated. The vehicle was towed to the residence and eventually towed to the dealer, but was not diagnosed or repaired. The dealer acknowledged the engine failure
... and that the failure was a common failure. The dealer declined the repair due to a lack of service records. The contact was offered a combustion cleaning; however, the vehicle was disabled. The manufacturer was notified of the failure. The approximate failure mileage was 95,000.Read more
Incident date: Apr 1, 2025
The driver seatbelt latch component failed. Unable to fasten the seat belt. This is a huge safety issue. It puts the driver and all passengers at risk. I received the recall in January due to having seatbelt latch issues on the second row. My kids safety was put at risk on the seatbelt latch not working properly on second row. I took my vehicle to dealership and it took couple of weeks for deale
... rship to receive the part to due backorder. This is the SECOND time that the driver seatbelt latch needs to be replaced within just a month and half. Huge safety issue. No warning icon for seatbelt latch failure. The software is also another recall that keeps need to be updating.Read more
Incident date: Apr 1, 2025
The driver seatbelt latch component failed. Unable to fasten the seat belt. This is a huge safety issue. It puts the driver and all passengers at risk. I received the recall in January due to having seatbelt latch issues on the second row. My kids safety was put at risk on the seatbelt latch not working properly on second row. I took my vehicle to dealership and it took couple of weeks for deale
... rship to receive the part to due backorder. This is the SECOND time that the driver seatbelt latch needs to be replaced within just a month and half. Huge safety issue. No warning icon for seatbelt latch failure. The software is also another recall that keeps need to be updating.Read more
Incident date: Jul 1, 2023
6.2L ENGINE NOISE AT START UP AND STAYS ON AND LOSES ENGINE POWER SLUGGISH ALL OF A SUDDEN WHILE DRIVING SAME ISSUE LIKE THE CURRENT RECALL ON ALL 6.2L EXCEPT MINE WAS BUILT RIGHT BEFORE APPROVED RECALL DATES BUT HAS SAME ENGINE L87 WITH SAME ISSUE AND IS CURRENTLY UNDRIVEABLE AND DANGEROUS IF TAKEN ON ROAD. REGULAR OIL CHANGES AT 50% OIL LIFE WITH RECOMMENDED MOBIL1 OIL & ACDELCO OIL FILTER.
Incident date: Mar 12, 2026
A loud clicking and popping sound while turning the car at low speeds, attributed most likely to the CV joint. The sound is happening more and more frequently.
Incident date: Mar 12, 2026
The contact owns a 2022 Ram 2500. The contact stated that while driving at an undisclosed speed, the RPM fluctuated. Additionally, the vehicle made an abnormal sound while slowing down to come to a stop. The vehicle was taken to the dealer, who discovered burnt transmission fluid and replaced the transmission, but the failure persisted. The vehicle was taken back to the dealer; however, the cause
... of the failure could not be determined. The vehicle was not repaired. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 10,000.Read more
Incident date: Mar 11, 2026
The contact owns a 2022 Ford Bronco Sport. The contact received notification of NHTSA Campaign Number: 25V467000 (Fuel System, Gasoline). The contact stated that while driving with the RPM at 2,000 RPM, the vehicle sputtered and skipped, with the check engine and power train warning lights illuminated. The vehicle was taken to a dealer where it was diagnosed, and determined that the fuel injectors
... needed to be replaced, but parts for the recall repair were not yet available. The manufacturer was not notified of the failure. The failure mileage was unknown.Read more
Incident date: Feb 27, 2026
My 2015 Ford Edge suddenly turned into a nightmare on what started as a normal drive. I noticed the temperature gauge climbing quickly, the engine started overheating, and then the check engine light came on. Almost at the same time, the engine began feeling like it was slipping—power dropped off, it hesitated and ran rough under acceleration, almost as if the transmission were slipping, but it
... was the engine itself struggling from poor lubrication. Turns out coolant had gotten into the oil (a pretty common headache with these 3.5L V6 models, often from a failing internal water pump). The mixture turned my oil into a gross, milky sludge that couldn't lubricate the engine properly anymore, leading to overheating and a slipping sensation as things started to bind up inside. I had to pull over quickly before it got even worse—definitely not something I want to go through again.Read more
Incident date: Mar 13, 2026
I had two codes on my 2022 Forester over last two weeks. First one u0284 was for the Active Grill Shutter. This happened because for some reason Subaru decided to put the fog lights on the same fuse as the AGS. Fog light blew, shorted out blew the fuse, this caused every safety system in the car to turn off. By default these are open so why does loosing 1-2MPG, or longer time to warm up a
... car cause every safety feature to turn off. Answer is they kill everything so you have to come in and pay hundreds for $15 bulb. This week had a o2 sensor go bad while I was driving. Had lane assist on , adaptive cruise, etc. Check engine went on and car start to rapidly decelerate, and again all safety features where turned off for something that is not fixed would potential cause reduce MPG, damage the catalytic converter, cause black smoke. None of this should require all safety features to be turned off. This is going to kill someone. I know your not suppose to have your hands off the wheel when using lane assist but people do it. I was in bumper to bumper traffic on 40 going 65 MPH. Not only would I have been at risk but everyone around me. Worse case is I do not have my hands on the wheel, the o2 sensor fails, car pulls into the car beside me and someone dies because Subaru wants money more than safety.Read more
Incident date: Mar 13, 2026
I had two codes on my 2022 Forester over last two weeks. First one u0284 was for the Active Grill Shutter. This happened because for some reason Subaru decided to put the fog lights on the same fuse as the AGS. Fog light blew, shorted out blew the fuse, this caused every safety system in the car to turn off. By default these are open so why does loosing 1-2MPG, or longer time to warm up a
... car cause every safety feature to turn off. Answer is they kill everything so you have to come in and pay hundreds for $15 bulb. This week had a o2 sensor go bad while I was driving. Had lane assist on , adaptive cruise, etc. Check engine went on and car start to rapidly decelerate, and again all safety features where turned off for something that is not fixed would potential cause reduce MPG, damage the catalytic converter, cause black smoke. None of this should require all safety features to be turned off. This is going to kill someone. I know your not suppose to have your hands off the wheel when using lane assist but people do it. I was in bumper to bumper traffic on 40 going 65 MPH. Not only would I have been at risk but everyone around me. Worse case is I do not have my hands on the wheel, the o2 sensor fails, car pulls into the car beside me and someone dies because Subaru wants money more than safety.Read more
Incident date: Mar 12, 2026
To Whom It May Concern, I am the owner of a 2026 Honda CBR600RR. I recently learned that this motorcycle is affected by an active recall related to potential engine defects that can lead to oil loss, rod bearing failure, and possible rear wheel lock. As a new rider, I do not feel safe operating this motorcycle until the recall repair is fully implemented. The first stage of the recall was comple
... ted prior to my purchase, but the defect persists and the permanent remedy is not yet available. I request the following actions be documented and addressed: 1.Official acknowledgement of my safety concern and that the bike is currently unsafe to ride. 2.Escalation to Honda Customer Relations for review of transport assistance, towing, or other options while the recall repair is pending. 3.Notification to NHTSA of my ongoing safety concerns, including my inability to safely ride the motorcycle. 4.Documentation of the unresolved recall and any potential next steps, including eligibility for goodwill compensation or buyback if the defect cannot be repaired promptly. I appreciate your prompt attention to this serious safety concern and ask that all communications and documentation be retained for my records.Read more
Incident date: Feb 24, 2026
The brake booster vacuum pump, in the words of Meineke, massive failure. The pump locked up and exploded, there are parts of at least under the valve cover. The failure resulted in the ruining of the camshaft, as this pump is controlled by the camshaft. The end of my camshaft looks like a mushroom head. This failure is currently in the investigation part of a class action law suit in which I am ad
... ding my name to the hat. My wife was driving at the time and fortunately was not injured during this catastrophic failure with what seems like planned obsolescence. I am also glad the kids weren’t in the car when this happened. We had just crossed 100k miles.Read more
Incident date: Feb 28, 2026
I was driving my car and my car all of a sudden dropped speed and when I pressed the gas my car started shaking and jerking.
Incident date: Feb 28, 2026
I was driving my car and my car all of a sudden dropped speed and when I pressed the gas my car started shaking and jerking.
Incident date: Dec 1, 2025
Vehicle experienced a catastrophic mechanical failure characterized by a percussive "shotgun blast" noise from the rear chassis, followed by an immediate, total loss of braking power (pedal to the floor) and a violent loss of directional stability. This incident represents an aggravated safety failure of known GMT900 platform defects. The technical chain of causality began with the factory exhaust
... manifold fasteners suffering a metallurgical shear, a universal defect documented under GM Bulletins 19-NA-218, PIP5075, and PIP4701. This shear created a high-velocity, high-heat exhaust leak directed at the brake master cylinder and vacuum assembly. This "heat soak" event compromised the engine-mounted mechanical Brake Vacuum Pump (Recall N192268490 / NHTSA 19V645) and destroyed the internal seals of the Master Cylinder (Special Coverage 15143 / NHTSA 11V599), resulting in total depletion of vacuum assist and hydraulic pressure. Simultaneously, the "shotgun blast" and violent swerve were caused by structural failure consistent with Rear Brake Caliper Bolt Fracture (GM 13247 / NHTSA 13V342) and Rear Axle Shaft/Pin Fracture (GM 14892 / NHTSA 14V819). This mechanical collapse caused the caliper to strike the wheel, resulting in a catastrophic rim blowout and immediate loss of tire pressure. Despite the vehicle having aftermarket long-tube headers installed, the root cause of the heat-related brake failure was the failure of the OEM GM manifold fasteners which snapped off in the cylinder head, as documented in the aforementioned bulletins. Under the Magnuson-Moss Warranty Act, the manufacturer remains liable for these pre-existing safety-critical defects. The vehicle is at Glenn Polk Chevrolet for a 901-series Product Allegation Investigation (Case #90199492). This report is filed to demand federal oversight into these life-threatening defects. The combo of failed fasteners, rim blowout, and compromised braking created a vehicle that was both unable to be steered or stoppedRead more
Incident date: Dec 1, 2025
Vehicle experienced a catastrophic mechanical failure characterized by a percussive "shotgun blast" noise from the rear chassis, followed by an immediate, total loss of braking power (pedal to the floor) and a violent loss of directional stability. This incident represents an aggravated safety failure of known GMT900 platform defects. The technical chain of causality began with the factory exhaust
... manifold fasteners suffering a metallurgical shear, a universal defect documented under GM Bulletins 19-NA-218, PIP5075, and PIP4701. This shear created a high-velocity, high-heat exhaust leak directed at the brake master cylinder and vacuum assembly. This "heat soak" event compromised the engine-mounted mechanical Brake Vacuum Pump (Recall N192268490 / NHTSA 19V645) and destroyed the internal seals of the Master Cylinder (Special Coverage 15143 / NHTSA 11V599), resulting in total depletion of vacuum assist and hydraulic pressure. Simultaneously, the "shotgun blast" and violent swerve were caused by structural failure consistent with Rear Brake Caliper Bolt Fracture (GM 13247 / NHTSA 13V342) and Rear Axle Shaft/Pin Fracture (GM 14892 / NHTSA 14V819). This mechanical collapse caused the caliper to strike the wheel, resulting in a catastrophic rim blowout and immediate loss of tire pressure. Despite the vehicle having aftermarket long-tube headers installed, the root cause of the heat-related brake failure was the failure of the OEM GM manifold fasteners which snapped off in the cylinder head, as documented in the aforementioned bulletins. Under the Magnuson-Moss Warranty Act, the manufacturer remains liable for these pre-existing safety-critical defects. The vehicle is at Glenn Polk Chevrolet for a 901-series Product Allegation Investigation (Case #90199492). This report is filed to demand federal oversight into these life-threatening defects. The combo of failed fasteners, rim blowout, and compromised braking created a vehicle that was both unable to be steered or stoppedRead more
Incident date: Dec 1, 2025
Vehicle experienced a catastrophic mechanical failure characterized by a percussive "shotgun blast" noise from the rear chassis, followed by an immediate, total loss of braking power (pedal to the floor) and a violent loss of directional stability. This incident represents an aggravated safety failure of known GMT900 platform defects. The technical chain of causality began with the factory exhaust
... manifold fasteners suffering a metallurgical shear, a universal defect documented under GM Bulletins 19-NA-218, PIP5075, and PIP4701. This shear created a high-velocity, high-heat exhaust leak directed at the brake master cylinder and vacuum assembly. This "heat soak" event compromised the engine-mounted mechanical Brake Vacuum Pump (Recall N192268490 / NHTSA 19V645) and destroyed the internal seals of the Master Cylinder (Special Coverage 15143 / NHTSA 11V599), resulting in total depletion of vacuum assist and hydraulic pressure. Simultaneously, the "shotgun blast" and violent swerve were caused by structural failure consistent with Rear Brake Caliper Bolt Fracture (GM 13247 / NHTSA 13V342) and Rear Axle Shaft/Pin Fracture (GM 14892 / NHTSA 14V819). This mechanical collapse caused the caliper to strike the wheel, resulting in a catastrophic rim blowout and immediate loss of tire pressure. Despite the vehicle having aftermarket long-tube headers installed, the root cause of the heat-related brake failure was the failure of the OEM GM manifold fasteners which snapped off in the cylinder head, as documented in the aforementioned bulletins. Under the Magnuson-Moss Warranty Act, the manufacturer remains liable for these pre-existing safety-critical defects. The vehicle is at Glenn Polk Chevrolet for a 901-series Product Allegation Investigation (Case #90199492). This report is filed to demand federal oversight into these life-threatening defects. The combo of failed fasteners, rim blowout, and compromised braking created a vehicle that was both unable to be steered or stoppedRead more
Incident date: Jan 30, 2026
Engine lights on Glass Recalibration failed multiple times. Engine failure when Jeep comes to a complete stop vehicle totally shuts down and needs to be restarted. When manufacture was contacted: not able to sell new engine. Resolution used engine with same issue. No real Resolution.
Incident date: Feb 16, 2026
While driving a flashing engine light came on in my 2019 Hyundai Tucson. This made the car slow down and have no power. I brought the car to the nearest mechanic, they told me it was the knock sensor and told me it was a recall for this car, I should bring it back to the dealership. I called the dealership and they had told me to bring the car in. They inspected the car on 8/30/24 at 44,990 mile
... s and told me it was the knock sensor and replaced it. On 11/4/24 at 46,246 miles the car was brought back in for the same issue and the car was inspected again, it was the knock sensor. This time the software was replaced. On 1/29/25 at 48,042 while driving on a highway going 70 mph the flashing light comes on again, brought it back to the dealership and I was given a loaner. The reached out to me and told me it was the knock sensor. They had the car for about 5 days. On 2/14/25 at 48,248 again, driving on a highway the flashing engine light appears again. Called the dealership and brought in the car and again, the knock sensor. On 12/31/25 at 56,712, driving on the highway, the flashing light appears again...On 1/2/26 the car goes back to the dealership, they call me and said that it's the strangest thing, the serpentine belt is worn, and it was making a banging sound which was setting off the knock sensor. At this point they offered to put in a new serpentine belt. I refused because after 5 failed attempts, I decided to bring it to my mechanic (I had lost all confidence with Hyundai mechanics). He did replace it. At this point I sent a letter to Hyundai motors stating all the facts that have been happening and asked for a buyout. After their investigation they called me and said, because you brought it to your mechanic they couldn't help me, but, if it happens again, bring it back to Hyundai. On 2/2/26, 57,286, again. I called the dealership and brought it back. This time they said that they didn't have a loaner to give so I rented one, 4 days. This is 5 failed attemptsRead more
Incident date: Feb 16, 2026
The power tailgate system on my Honda Odyssey failed. The dashboard displays a “Power Tailgate Problem” warning message and the tailgate will not open automatically using the key fob, interior button, or rear handle. When attempting to open it electronically, the vehicle beeps but the tailgate does not move. The tailgate can only be opened manually. The vehicle and tailgate system are availabl
... e for inspection upon request. The failure creates a safety risk because the tailgate cannot be opened electronically in situations where quick access to the rear cargo area may be needed. Additionally, if the power tailgate system fails unexpectedly, it could malfunction while opening or closing, potentially striking someone or failing during loading/unloading. The inability to rely on the automatic tailgate also creates hazards when carrying items or supervising children around the rear of the vehicle. The problem occurs consistently every time the power tailgate button is pressed. The system beeps but does not open. The issue has not yet been formally inspected by a dealer but can be easily reproduced. The vehicle has not yet been inspected by the manufacturer, police, or insurance representatives for this issue. A “Power Tailgate Problem” warning message appeared on the dashboard when attempting to use the power tailgate. At the same time, the vehicle emits a beep but the tailgate does not move. The issue began recently and has occurred every time the power tailgate has been used since the warning firstRead more
Incident date: Dec 5, 2025
Driving 40 mph coming around a bend. There was a car stopped about to rear off to the left and when coming up around the turn I saw and tried to stop. I was about two car lengths behind the car when I pressed the brake down and I pushed it all the way down and nothing happened. It was grinding and shaky when pressing it down. Not tight or anything. I feel like I normally would have that tension ri
... ght away to be able to stop. There was no warning or anything and the car always has warnings when something is close.Read more
Crash
Incident date: Dec 5, 2025
Driving 40 mph coming around a bend. There was a car stopped about to rear off to the left and when coming up around the turn I saw and tried to stop. I was about two car lengths behind the car when I pressed the brake down and I pushed it all the way down and nothing happened. It was grinding and shaky when pressing it down. Not tight or anything. I feel like I normally would have that tension ri
... ght away to be able to stop. There was no warning or anything and the car always has warnings when something is close.Read more
Crash
Incident date: Feb 2, 2026
Worn or broken Bushings control arm is under warranty but Tesla service declined to cover it under warranty I have checked all reviews and feedback This issue is under warranty and free of charge by Tesla service
Incident date: Oct 22, 2025
This car is a very well-maintained, low-use vehicle with regular oil changes and routine maintenance performed on schedule. Early in this drive, I noticed an unusual hissing sound as I approached a stop. When I tried to brake, I realized my brakes didn't seem to be responding. I pressed the brake pedal harder and realized that with 50-100 pounds of pressure (guess), I could slow the car down.
... As I came to a stop, the engine died. I restarted the car, and it died again immediately. After the following restart, I realized I could manually keep the RPM up in neutral while at stops, and press with significant force to get the car to stop. Had I not been comfortable two foot driving or understood the issue, this surely would have resulted in a crash of some sort. The car indicated a check engine light, loss of traction control, a flashing BRAKE light, and a flashing cruise control light. I took the car immediately to a local shop where they identified the problem as a vacuum leak at the brake booster. The plastic piece that the hose clamps onto had cracked off, leading to this problem. This make and model does not seem to have a check valve downstream of this component.Read more
Incident date: May 1, 2024
The contact owns a 2019 Ford Fiesta. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention). The contact stated that prior to receiving the recall notification, the camera had been intermittently showing a blank image, or the display screen was blue, or the image was frozen. The contact stated that the camera was no longer operational. The contact had not cont
... acted a dealer or the manufacturer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not informed of the failure. The failure mileage was approximately 170,000.Read more