Severe frame rust. 2 large holes on the inside of the frame just back from the front wheels and 2 large holes at the ends of the rear crossmember.
Odometer Fraud. The contact investigated a 2003 Toyota 4 Runner. The contact stated that during the investigation, he discovered a fraudulent scheme of approximately 15 vehicles with odometer fraud. The contact stated that the suspects targeted Facebook Marketplace victims by spraying oil on the engine prior to test-driving the vehicle, and when the vehicle began smoking, the suspects would ask for a discount for the vehicle. The contact added that after the vehicle was purchased, the odometer was rolled back and the vehicle was resold. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 150,000, and at the time of the vehicle being sold, it was discovered that the mileage was 306,000.
While my mechanic was servicing a small exhaust leak on my vehicle he noticed that the chassis/frame of the vehicle was heavily corroded. He told me that he believe it was no longer safe to drive and that I contact Toyota. I had a local Toyota service center also look at it and they confirmed that the chassis/frame was heavily corroded and unsafe to drive.
My vehicle: 2003 4Runner SR5 2WD VIN: [XXX] Issue: Front driver's side door will not open. Electronic locks are operating, but the door release is not functioning. Safety Concern: What if I was in a situation where I did need to get out of the vehicle immediately? Such as a high-water incident, fire, etc. Especially for a person [XXX], as myself, this would be a big issue. When attempting to exit the car after pulling into the driveway, I could not open the driver's door. The locks would release, but the door latch would not. I had to crawl over the console to get out through the passenger side. This was not easy as I had back fusion surgery and 8 disc replaced, fused. I had to open the sunroof to help with get over and out. After I did get out, I tried the key in the driver's door, it would actuate the door locks on all doors, but the driver's side door latch would still not release. I even disconnected the battery and reconnected. No help. And after knowing more, it was not an electrical issue, but mechanical failure. I now have it at the repair shop after talking with Toyota Service manage who admitted it was a poor design as the repair for this is to destroy the door panel to get to the actuator to attempt to release the door latch. The estimate for this work is 1,150.00. I am beyond frustration, and especially when I see there is no recall for this issue. There are penty of conversations on this same issue on 4Runner forums as well as all over YouTube. Thank you for looking into this. You can reach me at: [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Toyota has had issues with their frames rusting out and the 4th generation 4Runner is not exempt from this issue. My 2003 is requiring extensive work to keep it on the road safely due to frame rust. A recall to replace frames should be in place.
There is major corrosion on the chassis, brake-power steering-transmission lines, and all metal brackets on the frame and engine. The corrosion is so bad there is holes on the chassis. Known issue, many complaints, Toyota Corp. says to keep calling back maybe something will be done in the future. Unable to upload photos!
Severe frame rust, there was a recall for tacomas but 4Runners have the issue just as bad
The contact owns a 2003 Toyota 4Runner. The contact stated that upon taking the vehicle to several independent mechanics for servicing, he was informed that the subframe was significantly corroded and needed to be replaced. The vehicle was not repaired. The dealer was not notified of the failure. The manufacturer was notified of the failure and informed the contact the vehicle was not covered under recall. The failure mileage was approximately 115,000.
Frame is rotted from front to back
The contact owns a 2003 Toyota 4Runner. The contact stated that while the vehicle was at the tire retailer for tire replacement, the technician informed him that the subframe was corroded. The vehicle was then taken to an independent mechanic, who diagnosed that the passenger's side front and rear subframes were severely corroded, as well as the cross member. The mechanic advised the contact to stop driving the vehicle. The dealer was made aware of the failure and informed the contact that there was no recall associated with the VIN. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 165,000.
The VSC system in the vehicle becomes disabled due to a firmware 'glitch' identified by Toyota when an emission system issue is detected by the onboard diagnostic system. The VSC system is listed as an 'essential safety feature,' so I'm curious why a recall was never ordered to patch defective firmware that can cause VSC to become disabled due to a completely unrelated emissions issue.
Extensive rust through out frame, resulting in holes in structural members. Leaving frame in a weak and vulnerable state.
I purchased this 2003 Toyota 4Runner in 2018 under what I assumed was prime condition, for a vehicle that spent the majority of its life in Nebraska/Kansas before I moved to Texas in 2021. At 87,400 miles at the time of purchase, the vehicle had no visible damage to the exterior besides a few paint chips, some minor hail damage and scratches, and some easily fixed surface rust in the paint on the tailgate. The previous owner had driven it leisurely and had kept the miles low after 15 years. The car has had some mechanical issues, but nothing out of the ordinary outside of some regular maintenance over the first few years. Being close to 100,000 miles, the timing belt and pump was replaced around 98,000 miles. Other issues have been fixed periodically, please reference the attached files. After joining a Toyota 4Runner 4th Generation Facebook group and seeing a post about another's issues with rust damage in October 2020, I decided to take a look at my own frame. I then inspected my own vehicle, and found significant frame rot damage. It is extensive, with significant rust to the frame, with large holes and soft patches that question the integrity of the frame and the safety of the vehicle on the road. Every time I hit a small bump or pothole, I fear the frame will crack and I will lose control as others have. I have not sought out professional repairs due to the extensive cost, and am awaiting the outcome of a current class action lawsuit by the Bell Legal Group. The 4th Generation Toyota 4Runner (2003-2009) is built on the exact same frame as the Toyota Tacoma of that era, yet while the Tacoma was recalled for frame rot, the 4Runner was not included, which I believe to be a gross oversight in previous legal proceedings. The 2003-2009 Toyota 4Runner is a reliable vehicle, but poses significant frame rot issues much earlier than should be expected.
I purchased this 2003 Toyota 4Runner in 2018 under what I assumed was prime condition, for a vehicle that spent the majority of its life in Nebraska/Kansas before I moved to Texas in 2021. At 87,400 miles at the time of purchase, the vehicle had no visible damage to the exterior besides a few paint chips, some minor hail damage and scratches, and some easily fixed surface rust in the paint on the tailgate. The previous owner had driven it leisurely and had kept the miles low after 15 years. The car has had some mechanical issues, but nothing out of the ordinary outside of some regular maintenance over the first few years. Being close to 100,000 miles, the timing belt and pump was replaced around 98,000 miles. Other issues have been fixed periodically, please reference the attached files. After joining a Toyota 4Runner 4th Generation Facebook group and seeing a post about another's issues with rust damage in October 2020, I decided to take a look at my own frame. I then inspected my own vehicle, and found significant frame rot damage. It is extensive, with significant rust to the frame, with large holes and soft patches that question the integrity of the frame and the safety of the vehicle on the road. Every time I hit a small bump or pothole, I fear the frame will crack and I will lose control as others have. I have not sought out professional repairs due to the extensive cost, and am awaiting the outcome of a current class action lawsuit by the Bell Legal Group. The 4th Generation Toyota 4Runner (2003-2009) is built on the exact same frame as the Toyota Tacoma of that era, yet while the Tacoma was recalled for frame rot, the 4Runner was not included, which I believe to be a gross oversight in previous legal proceedings. The 2003-2009 Toyota 4Runner is a reliable vehicle, but poses significant frame rot issues much earlier than should be expected.
I purchased this 2003 Toyota 4Runner in 2018 under what I assumed was prime condition, for a vehicle that spent the majority of its life in Nebraska/Kansas before I moved to Texas in 2021. At 87,400 miles at the time of purchase, the vehicle had no visible damage to the exterior besides a few paint chips, some minor hail damage and scratches, and some easily fixed surface rust in the paint on the tailgate. The previous owner had driven it leisurely and had kept the miles low after 15 years. The car has had some mechanical issues, but nothing out of the ordinary outside of some regular maintenance over the first few years. Being close to 100,000 miles, the timing belt and pump was replaced around 98,000 miles. Other issues have been fixed periodically, please reference the attached files. After joining a Toyota 4Runner 4th Generation Facebook group and seeing a post about another's issues with rust damage in October 2020, I decided to take a look at my own frame. I then inspected my own vehicle, and found significant frame rot damage. It is extensive, with significant rust to the frame, with large holes and soft patches that question the integrity of the frame and the safety of the vehicle on the road. Every time I hit a small bump or pothole, I fear the frame will crack and I will lose control as others have. I have not sought out professional repairs due to the extensive cost, and am awaiting the outcome of a current class action lawsuit by the Bell Legal Group. The 4th Generation Toyota 4Runner (2003-2009) is built on the exact same frame as the Toyota Tacoma of that era, yet while the Tacoma was recalled for frame rot, the 4Runner was not included, which I believe to be a gross oversight in previous legal proceedings. The 2003-2009 Toyota 4Runner is a reliable vehicle, but poses significant frame rot issues much earlier than should be expected.
Vehicle frame has rusted through and has holes affecting structural condition.
Complete corrosion of entire frame causing unavoidable damage to framework.
There is severe rust on the frame, the rear is listing by 3/4 of an inch due to suspension rust, parts of the frame are perforated and lots of rust can fall out of drain holes when tapped. I am unable to steer the truck due to the intermediate steering column rust. The Tacoma was recalled for the same reason, I am assuming the 4runner has not been recalled because it was manufactured in greater numbers, and therefore more costly to repair, the danger of the severe rust is the same in both vehicles.
There is severe rust on the frame, the rear is listing by 3/4 of an inch due to suspension rust, parts of the frame are perforated and lots of rust can fall out of drain holes when tapped. I am unable to steer the truck due to the intermediate steering column rust. The Tacoma was recalled for the same reason, I am assuming the 4runner has not been recalled because it was manufactured in greater numbers, and therefore more costly to repair, the danger of the severe rust is the same in both vehicles.
There is severe rust on the frame, the rear is listing by 3/4 of an inch due to suspension rust, parts of the frame are perforated and lots of rust can fall out of drain holes when tapped. I am unable to steer the truck due to the intermediate steering column rust. The Tacoma was recalled for the same reason, I am assuming the 4runner has not been recalled because it was manufactured in greater numbers, and therefore more costly to repair, the danger of the severe rust is the same in both vehicles.
Excessive frame rust causing difficulty to keep vehicle on the road. No warning lamps, I noticed the rust starting years ago, now the rust is so bad that the frame is rusted through causing difficulty steering and loud crunch noises. I contacted Toyota Consumer Affairs explaining the rust concern and asked if I needed to take the vehicle to a dealership for inspection, they said it wasn’t necessary (sounds like they don’t want to admit the existence of a possible manufacturing defect). The vehicle is available for inspection. I feel like I would be doing a disservice to society if I continue to drive this vehicle on public roads due to the danger of injuring a pedestrian or another motorist.
Stabilizer bar connecting the axle to the frame rusted off. I was driving only 25-30mph at the time, luckily. The vehicle swayed violently almost causing an accident and nearly forcing me off the bridge I happened to driving over. Very fortunate no one was hurt and nothing was damaged from the incident. You can imagine the tragedy if that had happened on the highway driving 75mph! Major accident, innocent lives damaged or lost. This is a very dangerous vehicle not only to the driver and passengers but also to anybody that happened to be innocently in the path of an out of control Toyota 4runner. Toyota Please fix this, for your safety and everyone else on the highway. People should be warned!!
Stabilizer bar connected to the frame rusted off,back passenger side! Causing the vehicle to sway uncontrollably, due to the low rate of speed, I was able to regain control of my vehicle and not drive off the bridge I was driving over at the time or crash into another vehicle. The engine runs great, everything works, the vehicle still looks good but the frame is rusting out from underneath it! Toyota Needs To Make It Right!
Stabilizer bar connected to the frame rusted off,back passenger side! Causing the vehicle to sway uncontrollably, due to the low rate of speed, I was able to regain control of my vehicle and not drive off the bridge I was driving over at the time or crash into another vehicle. The engine runs great, everything works, the vehicle still looks good but the frame is rusting out from underneath it! Toyota Needs To Make It Right!
Stabilizer bar connecting the axle to the frame rusted off. I was driving only 25-30mph at the time, luckily. The vehicle swayed violently almost causing an accident and nearly forcing me off the bridge I happened to driving over. Very fortunate no one was hurt and nothing was damaged from the incident. You can imagine the tragedy if that had happened on the highway driving 75mph! Major accident, innocent lives damaged or lost. This is a very dangerous vehicle not only to the driver and passengers but also to anybody that happened to be innocently in the path of an out of control Toyota 4runner. Toyota Please fix this, for your safety and everyone else on the highway. People should be warned!!
So much rust has developed the frame is literally giving out. Toyota admitted to a rust issue- it’s now a safety issue with this generation of 4Runner. They did a recall on the same frame for Tacoma but not 4Runner.
The frame of the car has been rusting at a significant rate in the last 4 years. Mechanic identified major rust issues that would make the vehicle not safe in case of an accident.
The frame of the car has been rusting at a significant rate in the last 4 years. Mechanic identified major rust issues that would make the vehicle not safe in case of an accident.
The frame of the car has been rusting at a significant rate in the last 4 years. Mechanic identified major rust issues that would make the vehicle not safe in case of an accident.
The rust and corrosion underneath the vehicle continually gets worse year after year. The main components of vehicle relating to the engine, powertrain and suspension underneath vehicle are corroded; holes exist in the frame of the truck through out. The frame of truck is rotted due to not being sealed properly during the manufacturing process. Due to the rust and corrosion on the frame of truck, it is impossible to get work done on exhaust and muffler areas. I will send pictures for your reference. This makes driving a safety concern for myself and my son. At this time, I am unable to purchase a new car and do not have money to replace/fix the frame of truck. Inevitably, this problem will get worse and may cause a safety concern for myself and others on the road. I called Toyota on 4/12/22 and was told that there is not a recall for this issue and that any repairs would have to be paid by me. I then proceeded to call the number given to me by the representative to call 800-331-4331 for the Toyota Corporate office. I spoke to Blake who gave me the same answer, there was not a recall on this vehicle for rust/corrosion on the frame of vehicle. At this time, Toyota charges $150 just to check car and unfortunately, I don't have those funds to pay such a fee. I asked Blake if there was a way, Toyota can check without charging a fee and his answer was no. Currently, there is not any warning lights on, but with increased time and pressure of exhaust pipe and muffler will create more problems. I cannot have the exhaust system fixed until the frame of truck is replaced. My car was checked by an independent shop.
The rust and corrosion underneath the vehicle continually gets worse year after year. The main components of vehicle relating to the engine, powertrain and suspension underneath vehicle are corroded; holes exist in the frame of the truck through out. The frame of truck is rotted due to not being sealed properly during the manufacturing process. Due to the rust and corrosion on the frame of truck, it is impossible to get work done on exhaust and muffler areas. I will send pictures for your reference. This makes driving a safety concern for myself and my son. At this time, I am unable to purchase a new car and do not have money to replace/fix the frame of truck. Inevitably, this problem will get worse and may cause a safety concern for myself and others on the road. I called Toyota on 4/12/22 and was told that there is not a recall for this issue and that any repairs would have to be paid by me. I then proceeded to call the number given to me by the representative to call 800-331-4331 for the Toyota Corporate office. I spoke to Blake who gave me the same answer, there was not a recall on this vehicle for rust/corrosion on the frame of vehicle. At this time, Toyota charges $150 just to check car and unfortunately, I don't have those funds to pay such a fee. I asked Blake if there was a way, Toyota can check without charging a fee and his answer was no. Currently, there is not any warning lights on, but with increased time and pressure of exhaust pipe and muffler will create more problems. I cannot have the exhaust system fixed until the frame of truck is replaced. My car was checked by an independent shop.
The rust and corrosion underneath the vehicle continually gets worse year after year. The main components of vehicle relating to the engine, powertrain and suspension underneath vehicle are corroded; holes exist in the frame of the truck through out. The frame of truck is rotted due to not being sealed properly during the manufacturing process. Due to the rust and corrosion on the frame of truck, it is impossible to get work done on exhaust and muffler areas. I will send pictures for your reference. This makes driving a safety concern for myself and my son. At this time, I am unable to purchase a new car and do not have money to replace/fix the frame of truck. Inevitably, this problem will get worse and may cause a safety concern for myself and others on the road. I called Toyota on 4/12/22 and was told that there is not a recall for this issue and that any repairs would have to be paid by me. I then proceeded to call the number given to me by the representative to call 800-331-4331 for the Toyota Corporate office. I spoke to Blake who gave me the same answer, there was not a recall on this vehicle for rust/corrosion on the frame of vehicle. At this time, Toyota charges $150 just to check car and unfortunately, I don't have those funds to pay such a fee. I asked Blake if there was a way, Toyota can check without charging a fee and his answer was no. Currently, there is not any warning lights on, but with increased time and pressure of exhaust pipe and muffler will create more problems. I cannot have the exhaust system fixed until the frame of truck is replaced. My car was checked by an independent shop.
I have two 2003 Toyotas, a tundra and 4runner. The 4Runners frame is rusting out everywhere including the welds. My mechanic said it was getting to the point that it’s dangerous to drive and if it was in a wreck the frame would likely fail under the stress. My tundra frame from the same year is immaculate. I believe the are similar frames. This is obviously a defect in the production based on my readings and is very common. The investigation was opened in 2018 and its now 2022, when will this get addressed!
Frame has major rust holes towards the front inside next to the catalytic converters. Hoping to get them repaired before frame failure. The frame design is similar to the 2005 to 2015 Tacomas, which experienced similar issues with rust damage causing frame integrity issues. Toyota had a program to replaced those frames, but not for the 4Runners. The issue seems to be caused by certain factory openings in the frame that allow road salt to enter into the frame cavity, and cause the inside to rust. Being next to the catalytic converter, the heat accelerates the rust. On my 4Runner, the issue has gotten worse in the last 2 years. I cannot understand why Toyota covered all other trucks/suvs that use this similar frame but ignored the 4Runner.
The frame on my 4Runner is rusting through in multiple locations. The rear of the frame has already failed and a trailer I was pulling dragged on the road heavily as it failed. Definitely at risk of caving in long before the engine or transmitoo fails.
The frame on my vehicle is rusting prematurely. It's doing this on many other 4Runners and other Toyota trucks.
Crash
The frame has rusted out. It has many large holes throughout and will not pass State Inspection and is deemed unsafe.
The frame on my vehicle is rusting prematurely. It's doing this on many other 4Runners and other Toyota trucks.
Crash
The contact owns a 2003 Toyota 4Runner. The contact stated while his wife driving 60 MPH with the cruise control activated, the accelerator pedal was depressed, and the vehicle rapidly started to accelerate. The contact stated no warning light was illuminated. The driver depressed the brake pedal to stop the vehicle and parked on the side of the road. The driver was able to restart the vehicle and drive to her destination. The contact stated that in October 2021 his wife experienced a similar failure. The contact also stated that on 11/8/2021 while his wife driving 55 MPH and depressing the accelerator pedal, the vehicle accelerated quickly. The contact stated no warning light was illuminated. The driver depressed on the brake pedal with both feet and shifted gear to neutral to slow the vehicle. The driver stated she saw smoke coming from both front brakes. The drive was able to park on the side of the road. The driver stated that the brake pedal was seized on the floorboard. The driver stated she applied the parking brake to release the brake pedal. The driver was able to drive to her residence. The contact stated that his wife had experienced the failure on 3 different occasions. The vehicle was not diagnosed or repaired. A dealer was not contacted. The VIN was associated to NHTSA Campaign Number: 11V113000 (Vehicle Speed Control) and NHTSA Campaign Number: 03V146000 (Fuel System, Gasoline). The manufacturer had not been informed of the failure. The failure mileage was approximately 240,000.
The frame of the vehicle is rusted to the point my fist can fit through a hole in the frame.
The frame on the vehicle is rusting out. If not repaired, serious injury could occur if the frame breaks. A compromised frame could cause serious injury if an accident occurs. The driver side main frame has a gaping hole on the inside and another hole forming underneath that is in close proximity to the larger hole. The entire back cross bar member supporting the bumper is rusting out as well as the front cross bar member. The vehicle was inspected in July 2020 and the dealership said the frame was OK and had plenty of life left in it. After getting a muffler installed at a local independent shop in October 2021, the hole grabbed the attention of the technician. After inspecting, rusty flakes kept falling away.
Extreme frame rust. The vehicle has extreme frame rust and Toyota should be held accountable for poor quality frame material. I have heard tons of stories of other peoples steering components snapping due to rust and frame damage.
I own a 2003 Toyota 4Runner with very low mileage for its age. It has been garage kept for most of its life. I was experiencing difficulty steering, and when I took the car to a mechanic, it was determined that the frame was prematurely rusted and rotted to a dangerous level putting my life at risk while driving it.
I own a 2003 Toyota 4Runner with very low mileage for its age. It has been garage kept for most of its life. I was experiencing difficulty steering, and when I took the car to a mechanic, it was determined that the frame was prematurely rusted and rotted to a dangerous level putting my life at risk while driving it.
The frame is rusted very bad and it’s a major safety issue for this type of vehicle I don’t know when it’s going to fall apart. I am sure I am not the only one to have this problem.
I have not actually had an incident yet, but have been advised by the Toyota service team that I should no longer tow trailers and should consider not driving it at all due to frame rust/perforation in front of the rear control arms. This has been a well cared for vehicle that is in otherwise great shape (It has had every repair the dealership has ever recommended) the vehicle was bought per the dealerships claim that it could be driven "forever" as long as the dealership takes care of it. And now I'm faced with a massive expense to repair or replace the vehicle.
Vehicle frame and suspension components are completely rusting out. Having issues with the corroded steering column lower shaft not allowing the vehicle to turn properly.
Vehicle frame and suspension components are completely rusting out. Having issues with the corroded steering column lower shaft not allowing the vehicle to turn properly.
I have not actually had an incident yet, but have been advised by the Toyota service team that I should no longer tow trailers and should consider not driving it at all due to frame rust/perforation in front of the rear control arms. This has been a well cared for vehicle that is in otherwise great shape (It has had every repair the dealership has ever recommended) the vehicle was bought per the dealerships claim that it could be driven "forever" as long as the dealership takes care of it. And now I'm faced with a massive expense to repair or replace the vehicle.